Dlink dub-e100 Ubuntu 10.04

Добрвй вечер. Есть адаптер dlink dub e-100 и ubuntu 10.04 Модули asix usbnet есть но ifconfig eth1 up даёт ошибку.. Не подскажите куда копать?
uname -a
Linux smoke-SRV 2.6.32-45-generic #99-Ubuntu SMP Tue Oct 16 16:31:11 UTC 2012 i686 GNU/Linux

lsusb
Bus 003 Device 002: ID 2109:0811
Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 002 Device 005: ID 09da:0080 A4 Tech Co., Ltd
Bus 002 Device 004: ID 045e:0750 Microsoft Corp.
Bus 002 Device 003: ID 2001:1a02 D-Link Corp. [hex]
Bus 002 Device 002: ID 8087:0024
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 8087:0024
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

lsmod | grep usb
usbnet 14975 0
usbhid 36110 0
hid 67288 1 usbhid
mii 4381 3 usbnet,asix,r8169

lsmod | grep asix
asix 45481 0
mii 4381 3 usbnet,asix,r8169

ifconfig -a
eth0 Link encap:Ethernet HWaddr 14:da:e9:c6:9c:56
inet addr:192.168.1.94 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::16da:e9ff:fec6:9c56/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:949 errors:0 dropped:0 overruns:0 frame:0
TX packets:830 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1088445 (1.0 MB) TX bytes:125915 (125.9 KB)
Interrupt:28 Base address:0xa000

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:12 errors:0 dropped:0 overruns:0 frame:0
TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:720 (720.0 B) TX bytes:720 (720.0 B)

wlan0 Link encap:Ethernet HWaddr 74:2f:68:93:82:b6
inet6 addr: fe80::762f:68ff:fe93:82b6/64 Scope:Link
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:12 errors:0 dropped:0 overruns:0 frame:0
TX packets:11 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1492 (1.4 KB) TX bytes:2398 (2.3 KB)

ifconfig eth1 up
eth1: ERROR while getting interface flags: No such device

В файле asix.c прописан id адаптера

static const struct usb_device_id products [] = {
// DLink DUB-E100C
USB_DEVICE (0x2001, 0x1a02),
.driver_info = (unsigned long) &ax88772b_info,
}

Кстате заметил вот что
dmesg | grep usb
[ 0.567287] usbcore: registered new interface driver usbfs
[ 0.567295] usbcore: registered new interface driver hub
[ 0.567313] usbcore: registered new device driver usb
[ 1.201153] usb usb3: No SuperSpeed endpoint companion for config 1 interface 0 altsetting 0 ep 129: using minimum values
[ 1.388511] usb 1-1: new high speed USB device using ehci_hcd and address 2
[ 1.632142] usb 2-1: new high speed USB device using ehci_hcd and address 2
[ 1.875784] usb 3-1: new high speed USB device using xhci_hcd and address 2
[ 1.893346] usb 3-1: ep 0x81 - rounding interval to 2048 microframes
[ 2.035685] usb 2-1.4: new full speed USB device using ehci_hcd and address 3
[ 2.141925] input: A4Tech USB Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.4/2-1.4:1.0/input/input2
[ 2.142076] generic-usb 0003:09DA:0080.0001: input,hidraw0: USB HID v1.11 Mouse [A4Tech USB Mouse] on usb-0000:00:1d.0-1.4/input0
[ 2.142151] usbcore: registered new interface driver usbhid
[ 2.142153] usbhid: USB HID core driver
[ 2.199464] usb 2-1.5: new low speed USB device using ehci_hcd and address 4
[ 2.262494] usbcore: registered new interface driver asix
[ 2.323185] input: Microsoft Wired Keyboard 600 as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.5/2-1.5:1.0/input/input3
[ 2.323274] generic-usb 0003:045E:0750.0002: input,hidraw1: USB HID v1.11 Keyboard [Microsoft Wired Keyboard 600] on usb-0000:00:1d.0-1.5/input0
[ 2.328844] input: Microsoft Wired Keyboard 600 as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.5/2-1.5:1.1/input/input4
[ 2.328928] generic-usb 0003:045E:0750.0003: input,hidraw2: USB HID v1.11 Device [Microsoft Wired Keyboard 600] on usb-0000:00:1d.0-1.5/input1
[ 2.399207] usb 2-1.6: new high speed USB device using ehci_hcd and address 5

и
dmesg | grep eth
[ 1.057136] i2c-core: driver [adp5520] using legacy suspend method
[ 1.057138] i2c-core: driver [adp5520] using legacy resume method
[ 1.176906] r8169 0000:02:00.0: eth0: RTL8168b/8111b at 0xf801a000, 14:da:e9:c6:9c:56, XID 0c200000 IRQ 43
[ 15.372703] r8169 0000:02:00.0: eth0: link down
[ 15.372712] r8169 0000:02:00.0: eth0: link down
[ 15.372846] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 17.020601] r8169 0000:02:00.0: eth0: link up
[ 17.020719] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 27.385741] eth0: no IPv6 routers present

Проблема скорей всего вот в чём:
dmesg | tail
[ 36.547612] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
[ 36.547740] usb 3-1.3: ep 0x81 - rounding interval to 1024 microframes
[ 36.548768] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
[ 36.549293] xhci_hcd 0000:03:00.0: WARN: short transfer on control ep
[ 39.543803] usb 3-1.3: USB disconnect, address 3
[ 42.439481] usb 2-1.4: new high speed USB device using ehci_hcd and address 7
[ 49.715984] Intel AES-NI instructions are not detected.
[ 49.759834] padlock_aes: VIA PadLock not detected.
[ 215.294587] usb 2-1.4: USB disconnect, address 7
[ 219.325113] usb 2-1.4: new high speed USB device using ehci_hcd and address 8


Но решить пока не получается ((

Собственно если кому интересно. Решилось установикой 12.10 ))) все завелось из коробки...