Wi-Fi адаптер не настраивается

[console]
iwlist scan
lo Interface doesn't support scanning.

wlan0 Scan completed :
Cell 01 - Address: 00:1D:46:25:05:72
Channel:1
Frequency:2.412 GHz (Channel 1)
Quality=70/70 Signal level=-5 dBm
Encryption key:on
ESSID:"TPU Hostels"
Bit Rates:12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s; 48 Mb/s
54 Mb/s
Mode:Master
Extra:tsf=0000001196ebcee0
Extra: Last beacon: 1441ms ago
IE: Unknown: 000B54505520486F7374656C73
IE: Unknown: 010698243048606C
IE: Unknown: 030101
IE: Unknown: 0706555320010B1E
IE: Unknown: 0B050100020000
IE: Unknown: 2A0100
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : 802.1x
IE: Unknown: 851E02008F000F00FF0359004C49422D666C6F6F722E582E726F6F0001000027
IE: Unknown: 9606004096001100
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : TKIP
Authentication Suites (1) : 802.1x
IE: Unknown: DD180050F2020101800003000000270000004200000072000000
IE: Unknown: DD06004096010104
IE: Unknown: DD050040960305
IE: Unknown: DD050040960B09
IE: Unknown: DD050040961401
IE: Unknown: DD1D0040960C01FEA82336B8D22E010000701E00000000734504E4E06929B0
Cell 02 - Address: 00:1D:46:25:05:70
Channel:1
Frequency:2.412 GHz (Channel 1)
Quality=70/70 Signal level=-5 dBm
Encryption key:off
ESSID:"TPU Guest"
Bit Rates:12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s; 48 Mb/s
54 Mb/s
Mode:Master
Extra:tsf=0000001196eb6ca2
Extra: Last beacon: 1441ms ago
IE: Unknown: 0009545055204775657374
IE: Unknown: 010698243048606C
IE: Unknown: 030101
IE: Unknown: 0706555320010B1E
IE: Unknown: 0B050100020000
IE: Unknown: 2A0100
IE: Unknown: 3603721003
IE: Unknown: 851E02008F000F00FF0359004C49422D666C6F6F722E582E726F6F0001000027
IE: Unknown: 9606004096001100
IE: Unknown: DD180050F2020101800003000000270000004200000072000000
IE: Unknown: DD06004096010104
IE: Unknown: DD050040960305
IE: Unknown: DD050040960B09
IE: Unknown: DD050040961400
IE: Unknown: DD1D0040960C01FEA83B36B8D22E0100006E1E00000000F6A4DDE7C7E52B4D
Cell 03 - Address: 00:1D:46:25:05:77
Channel:1
Frequency:2.412 GHz (Channel 1)
Quality=70/70 Signal level=-5 dBm
Encryption key:on
ESSID:""
Bit Rates:12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s; 48 Mb/s
54 Mb/s
Mode:Master
Extra:tsf=0000001196ec7034
Extra: Last beacon: 1461ms ago
IE: Unknown: 000100
IE: Unknown: 010698243048606C
IE: Unknown: 030101
IE: Unknown: 050400020000
IE: Unknown: 0706555320010B1E
IE: Unknown: 0B050100020000
IE: Unknown: 2A0100
IE: Unknown: 851E02008F000F00FF0359004C49422D666C6F6F722E582E726F6F0001000027
IE: Unknown: 9606004096001100
IE: Unknown: DD180050F2020101800003000000270000004200000072000000
IE: Unknown: DD06004096010104
IE: Unknown: DD050040960305
IE: Unknown: DD050040960B09
IE: Unknown: DD050040961400
IE: Unknown: DD1D0040960C01FEA8B635B8D22E010000A32803000000B6939AE996C0B0F1
Cell 04 - Address: 00:1D:46:25:05:71
Channel:1
Frequency:2.412 GHz (Channel 1)
Quality=70/70 Signal level=-5 dBm
Encryption key:on
ESSID:"TPU Public"
Bit Rates:12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s; 48 Mb/s
54 Mb/s
Mode:Master
Extra:tsf=0000001196ec7034
Extra: Last beacon: 1424ms ago
IE: Unknown: 000A545055205075626C6963
IE: Unknown: 010698243048606C
IE: Unknown: 030101
IE: Unknown: 0706555320010B1E
IE: Unknown: 0B050100020000
IE: Unknown: 2A0100
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : 802.1x
IE: Unknown: 851E02008F000F00FF0359004C49422D666C6F6F722E582E726F6F0001000027
IE: Unknown: 9606004096001100
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : TKIP
Authentication Suites (1) : 802.1x
IE: Unknown: DD180050F2020101800003000000270000004200000072000000
IE: Unknown: DD06004096010104
IE: Unknown: DD050040960305
IE: Unknown: DD050040960B09
IE: Unknown: DD050040961401
IE: Unknown: DD1D0040960C01FEA80B36B8D22E0100006F1E00000000E83AFEB0D37068A6
Cell 05 - Address: 00:1C:F9:72:A8:61
Channel:6
Frequency:2.437 GHz (Channel 6)
Quality=70/70 Signal level=-6 dBm
Encryption key:on
ESSID:"TPU Public"
Bit Rates:12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s; 48 Mb/s
54 Mb/s
Mode:Master
Extra:tsf=000000114f4fe16f
Extra: Last beacon: 875ms ago
IE: Unknown: 000A545055205075626C6963
IE: Unknown: 010698243048606C
IE: Unknown: 030106
IE: Unknown: 0706525520010D14
IE: Unknown: 0B050000090000
IE: Unknown: 2A0100
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : 802.1x
IE: Unknown: 851E02008F000F00FF0359004C49422D666C6F6F722E582E726F6F0000000027
IE: Unknown: 9606004096000E00
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : TKIP
Authentication Suites (1) : 802.1x
IE: Unknown: DD180050F2020101800003000000270000004200000072000000
IE: Unknown: DD06004096010104
IE: Unknown: DD050040960305
IE: Unknown: DD050040960B09
IE: Unknown: DD050040961401
IE: Unknown: DD1D0040960C01C305428ACAD22E010000F52900000000B31299BBF593121B
Cell 06 - Address: 00:1C:F9:72:A8:66
Channel:6
Frequency:2.437 GHz (Channel 6)
Quality=70/70 Signal level=-6 dBm
Encryption key:on
ESSID:"TPU VIP"
Bit Rates:12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s; 48 Mb/s
54 Mb/s
Mode:Master
Extra:tsf=000000114f4fb3e1
Extra: Last beacon: 874ms ago
IE: Unknown: 000754505520564950
IE: Unknown: 010698243048606C
IE: Unknown: 030106
IE: Unknown: 0706525520010D14
IE: Unknown: 0B050000090000
IE: Unknown: 2A0100
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : 802.1x
IE: Unknown: 851E02008F000F00FF0359004C49422D666C6F6F722E582E726F6F0000000027
IE: Unknown: 9606004096000E00
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : TKIP
Authentication Suites (1) : 802.1x
IE: Unknown: DD180050F2020101800003000000270000004200000072000000
IE: Unknown: DD06004096010104
IE: Unknown: DD050040960305
IE: Unknown: DD050040960B09
IE: Unknown: DD050040961401
IE: Unknown: DD1D0040960C01C3054D8ACAD22E010000F729000000001B522B541D1858A1
Cell 07 - Address: 00:1C:F9:72:A8:62
Channel:6
Frequency:2.437 GHz (Channel 6)
Quality=70/70 Signal level=-6 dBm
Encryption key:on
ESSID:"TPU Hostels"
Bit Rates:12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s; 48 Mb/s
54 Mb/s
Mode:Master
Extra:tsf=000000114f4fa034
Extra: Last beacon: 867ms ago
IE: Unknown: 000B54505520486F7374656C73
IE: Unknown: 010698243048606C
IE: Unknown: 030106
IE: Unknown: 0706525520010D14
IE: Unknown: 0B050000090000
IE: Unknown: 2A0100
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : 802.1x
IE: Unknown: 851E02008F000F00FF0359004C49422D666C6F6F722E582E726F6F0000000027
IE: Unknown: 9606004096000E00
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : TKIP
Authentication Suites (1) : 802.1x
IE: Unknown: DD180050F2020101800003000000270000004200000072000000
IE: Unknown: DD06004096010104
IE: Unknown: DD050040960305
IE: Unknown: DD050040960B09
IE: Unknown: DD050040961401
IE: Unknown: DD1D0040960C01C3055A8ACAD22E010000F629000000000FC97CF812AAC511
Cell 08 - Address: 00:1D:46:25:05:76
Channel:1
Frequency:2.412 GHz (Channel 1)
Quality=70/70 Signal level=-5 dBm
Encryption key:on
ESSID:"TPU VIP"
Bit Rates:12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s; 48 Mb/s
54 Mb/s
Mode:Master
Extra:tsf=0000001196ec0025
Extra: Last beacon: 1441ms ago
IE: Unknown: 000754505520564950
IE: Unknown: 010698243048606C
IE: Unknown: 030101
IE: Unknown: 0706555320010B1E
IE: Unknown: 0B050100020000
IE: Unknown: 2A0100
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : 802.1x
IE: Unknown: 851E02008F000F00FF0359004C49422D666C6F6F722E582E726F6F0001000027
IE: Unknown: 9606004096001100
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : TKIP
Authentication Suites (1) : 802.1x
IE: Unknown: DD180050F2020101800003000000270000004200000072000000
IE: Unknown: DD06004096010104
IE: Unknown: DD050040960305
IE: Unknown: DD050040960B09
IE: Unknown: DD050040961401
IE: Unknown: DD1D0040960C01FEA81736B8D22E010000711E00000000AAD7068F9994A0F4
Cell 09 - Address: 00:1C:F9:72:A8:60
Channel:6
Frequency:2.437 GHz (Channel 6)
Quality=70/70 Signal level=-6 dBm
Encryption key:off
ESSID:"TPU Guest"
Bit Rates:12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s; 48 Mb/s
54 Mb/s
Mode:Master
Extra:tsf=000000114f4f01f6
Extra: Last beacon: 883ms ago
IE: Unknown: 0009545055204775657374
IE: Unknown: 010698243048606C
IE: Unknown: 030106
IE: Unknown: 0706525520010D14
IE: Unknown: 0B050000090000
IE: Unknown: 2A0100
IE: Unknown: 3603721003
IE: Unknown: 851E02008F000F00FF0359004C49422D666C6F6F722E582E726F6F0000000027
IE: Unknown: 9606004096000E00
IE: Unknown: DD180050F2020101800003000000270000004200000072000000
IE: Unknown: DD06004096010104
IE: Unknown: DD050040960305
IE: Unknown: DD050040960B09
IE: Unknown: DD050040961400
IE: Unknown: DD1D0040960C01C305728ACAD22E010000F429000000000EACBEC587355AA6
Cell 10 - Address: 00:1D:46:27:FF:36
Channel:6
Frequency:2.437 GHz (Channel 6)
Quality=70/70 Signal level=-17 dBm
Encryption key:on
ESSID:"TPU VIP"
Bit Rates:12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s; 48 Mb/s
54 Mb/s
Mode:Master
Extra:tsf=000000260750a034
Extra: Last beacon: 872ms ago
IE: Unknown: 000754505520564950
IE: Unknown: 010698243048606C
IE: Unknown: 030106
IE: Unknown: 050400020000
IE: Unknown: 0706555320010B1E
IE: Unknown: 0B050000080000
IE: Unknown: 2A0100
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : 802.1x
IE: Unknown: 851E04008F000F00FF0359004C49422D4150303031642E343531660000000027
IE: Unknown: 9606004096001100
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : TKIP
Authentication Suites (1) : 802.1x
IE: Unknown: DD180050F2020101800003000000270000004200000072000000
IE: Unknown: DD06004096010104
IE: Unknown: DD050040960305
IE: Unknown: DD050040960B09
IE: Unknown: DD050040961401
IE: Unknown: DD1D0040960C01FEA872B97CCD2E010000792E03000000C13426EC059AA01F
Cell 11 - Address: 00:1D:46:27:FF:30
Channel:6
Frequency:2.437 GHz (Channel 6)
Quality=70/70 Signal level=-16 dBm
Encryption key:off
ESSID:"TPU Guest"
Bit Rates:12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s; 48 Mb/s
54 Mb/s
Mode:Master
Extra:tsf=0000002606ab0037
Extra: Last beacon: 11690ms ago
IE: Unknown: 0009545055204775657374
IE: Unknown: 010698243048606C
IE: Unknown: 030106
IE: Unknown: 050401020000
IE: Unknown: 0706555320010B1E
IE: Unknown: 0B0500000A0000
IE: Unknown: 2A0100
IE: Unknown: 3603721003
IE: Unknown: 851E04008F000F00FF0359004C49422D4150303031642E343531660000000027
IE: Unknown: 9606004096001100
IE: Unknown: DD180050F2020101800003000000270000004200000072000000
IE: Unknown: DD06004096010104
IE: Unknown: DD050040960305
IE: Unknown: DD050040960B09
IE: Unknown: DD050040961400
IE: Unknown: DD1D0040960C01FEA8B4B97CCD2E010000774103000000DF641476BF554148
Cell 12 - Address: 00:1D:46:27:FF:32
Channel:6
Frequency:2.437 GHz (Channel 6)
Quality=70/70 Signal level=-17 dBm
Encryption key:on
ESSID:"TPU Hostels"
Bit Rates:12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s; 48 Mb/s
54 Mb/s
Mode:Master
Extra:tsf=0000002607109034
Extra: Last beacon: 5058ms ago
IE: Unknown: 000B54505520486F7374656C73
IE: Unknown: 010698243048606C
IE: Unknown: 030106
IE: Unknown: 050400020000
IE: Unknown: 0706555320010B1E
IE: Unknown: 0B050000070000
IE: Unknown: 2A0100
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : 802.1x
IE: Unknown: 851E04008F000F00FF0359004C49422D4150303031642E343531660000000027
IE: Unknown: 9606004096001100
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : TKIP
Authentication Suites (1) : 802.1x
IE: Unknown: DD180050F2020101800003000000270000004200000072000000
IE: Unknown: DD06004096010104
IE: Unknown: DD050040960305
IE: Unknown: DD050040960B09
IE: Unknown: DD050040961401
IE: Unknown: DD1D0040960C01FEA89DB97CCD2E010000BB4203000000C1E8CA7831A9ECA8
Cell 13 - Address: 00:1D:46:27:FF:31
Channel:6
Frequency:2.437 GHz (Channel 6)
Quality=70/70 Signal level=-17 dBm
Encryption key:on
ESSID:"TPU Public"
Bit Rates:12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s; 48 Mb/s
54 Mb/s
Mode:Master
Extra:tsf=000000260750a034
Extra: Last beacon: 884ms ago
IE: Unknown: 000A545055205075626C6963
IE: Unknown: 010698243048606C
IE: Unknown: 030106
IE: Unknown: 050400020000
IE: Unknown: 0706555320010B1E
IE: Unknown: 0B050000080000
IE: Unknown: 2A0100
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : 802.1x
IE: Unknown: 851E04008F000F00FF0359004C49422D4150303031642E343531660000000027
IE: Unknown: 9606004096001100
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : TKIP
Authentication Suites (1) : 802.1x
IE: Unknown: DD180050F2020101800003000000270000004200000072000000
IE: Unknown: DD06004096010104
IE: Unknown: DD050040960305
IE: Unknown: DD050040960B09
IE: Unknown: DD050040961401
IE: Unknown: DD1D0040960C01FEA889B97CCD2E0100004045030000006DF60D8315D3F51E

eth0 Interface doesn't support scanning.
[/console]

[console]
conf.real line 821.
"/usr/sbin/drakbackup" is not executable [Backups] at /usr/sbin/drakconf.real line 821.
"/usr/sbin/drakvirt" is not executable [Virtualization] at /usr/sbin/drakconf.real line 821.
"/usr/sbin/tomoyo-gui" is not executable [Tomoyo Policy] at /usr/sbin/drakconf.real line 821.
Gtk-CRITICAL **: gtk_cell_view_set_cell_data: assertion `cell_view->priv->displayed_row != NULL' failed at /usr/lib/libDrakX/interactive/gtk.pm line 522.
Gtk-CRITICAL **: gtk_cell_view_set_cell_data: assertion `cell_view->priv->displayed_row != NULL' failed at /usr/lib/libDrakX/interactive/gtk.pm line 522.
Gtk-CRITICAL **: gtk_cell_view_set_cell_data: assertion `cell_view->priv->displayed_row != NULL' failed at /usr/lib/libDrakX/interactive/gtk.pm line 522.
Gtk-CRITICAL **: gtk_cell_view_set_cell_data: assertion `cell_view->priv->displayed_row != NULL' failed at /usr/lib/libDrakX/interactive/gtk.pm line 522.
Gtk-CRITICAL **: gtk_cell_view_set_cell_data: assertion `cell_view->priv->displayed_row != NULL' failed at /usr/lib/libDrakX/interactive/gtk.pm line 522.
Gtk-CRITICAL **: gtk_cell_view_set_cell_data: assertion `cell_view->priv->displayed_row != NULL' failed at /usr/lib/libDrakX/interactive/gtk.pm line 522.
Gtk-CRITICAL **: gtk_cell_view_set_cell_data: assertion `cell_view->priv->displayed_row != NULL' failed at /usr/lib/libDrakX/interactive/gtk.pm line 522.
Gtk-CRITICAL **: gtk_cell_view_set_cell_data: assertion `cell_view->priv->displayed_row != NULL' failed at /usr/lib/libDrakX/interactive/gtk.pm line 522.
Selected interface 'wlan0'
OK
Не удалось создать преобразователь имён узлов: Неверное имя узла
run-parts: /etc/sysconfig/network-scripts/hostname.d/avahi exited with return code 1
Перезагружается конфигурация vnstatd: [ ОК ]
Error for wireless request "Set Encode" (8B2A) :
invalid argument "s:".
Selected interface 'wlan0'
OK
[/console]

[console]
lsmod
Module Size Used by
ipt_IFWLOG 2002 2
ipt_psd 43043 1
cls_flow 6501 0
cls_fw 3283 0
cls_u32 5536 0
sch_htb 13384 0
sch_hfsc 16513 0
sch_ingress 1458 0
sch_sfq 4823 0
xt_time 1805 0
xt_connlimit 2948 0
xt_realm 714 0
iptable_raw 1774 0
xt_comment 720 18
xt_recent 8098 0
xt_policy 2158 0
ipt_ULOG 7490 0
ipt_REJECT 1933 4
ipt_REDIRECT 1494 0
ipt_NETMAP 1454 0
ipt_MASQUERADE 2016 0
ipt_ECN 1537 0
ipt_ecn 1121 0
ipt_CLUSTERIP 5761 0
ipt_ah 893 0
ipt_addrtype 1631 2
nf_nat_tftp 684 0
nf_nat_snmp_basic 7519 0
nf_nat_sip 5076 0
nf_nat_pptp 3942 0
nf_nat_proto_gre 2254 1 nf_nat_pptp
nf_nat_irc 1380 0
nf_nat_h323 7735 0
nf_nat_ftp 2604 0
nf_nat_amanda 846 0
ts_kmp 1565 5
nf_conntrack_amanda 2217 1 nf_nat_amanda
nf_conntrack_sane 4265 0
nf_conntrack_tftp 3600 1 nf_nat_tftp
nf_conntrack_sip 15796 1 nf_nat_sip
nf_conntrack_proto_sctp 10441 0
nf_conntrack_pptp 9891 1 nf_nat_pptp
nf_conntrack_proto_gre 5684 1 nf_conntrack_pptp
nf_conntrack_netlink 14883 0
nf_conntrack_netbios_ns 1254 0
nf_conntrack_irc 4231 1 nf_nat_irc
nf_conntrack_h323 57320 1 nf_nat_h323
nf_conntrack_ftp 10125 1 nf_nat_ftp
ipt_set 1143 2
ipt_SET 1335 0
ip_set_nethash 7507 0
ip_set_iptreemap 7764 0
ip_set_iptree 4861 2
ip_set_ipporthash 6508 0
ip_set_portmap 3164 0
ip_set_macipmap 3018 0
ip_set_ipmap 3040 0
ip_set_iphash 5833 0
ip_set 13331 18 ipt_set,ipt_SET,ip_set_nethash,ip_set_iptreemap,ip_set_iptree,ip_set_ipporthash,ip_set_portmap,ip_set_macipmap,ip_set_ipmap,ip_set_iphash
xt_TPROXY 1870 0
nf_tproxy_core 2056 1 xt_TPROXY,[permanent]
xt_tcpmss 1197 0
xt_pkttype 848 0
xt_physdev 1507 0
xt_owner 906 0
xt_NFQUEUE 1776 0
xt_NFLOG 841 0
nfnetlink_log 7208 1 xt_NFLOG
xt_multiport 2314 4
xt_MARK 743 1
xt_mark 711 0
xt_mac 772 0
xt_limit 1382 0
xt_length 936 0
xt_iprange 1902 0
xt_helper 1071 0
xt_hashlimit 8012 0
xt_DSCP 1677 0
xt_dscp 1301 0
xt_dccp 1797 0
xt_conntrack 2302 8
xt_CONNMARK 1145 0
xt_connmark 985 0
xt_CLASSIFY 723 0
ipt_LOG 4831 4
xt_tcpudp 2075 11
xt_state 1098 1
iptable_nat 5407 0
nf_nat 18994 12 ipt_REDIRECT,ipt_NETMAP,ipt_MASQUERADE,nf_nat_tftp,nf_nat_sip,nf_nat_pptp,nf_nat_proto_gre,nf_nat_irc,nf_nat_h323,nf_nat_ftp,nf_nat_amanda,iptable_nat
nf_conntrack_ipv4 12757 12 iptable_nat,nf_nat
nf_defrag_ipv4 1073 2 xt_TPROXY,nf_conntrack_ipv4
nf_conntrack 69310 31 xt_connlimit,ipt_MASQUERADE,ipt_CLUSTERIP,nf_nat_tftp,nf_nat_snmp_basic,nf_nat_sip,nf_nat_pptp,nf_nat_irc,nf_nat_h323,nf_nat_ftp,nf_nat_amanda,nf_conntrack_amanda,nf_conntrack_sane,nf_conntrack_tftp,nf_conntrack_sip,nf_conntrack_proto_sctp,nf_conntrack_pptp,nf_conntrack_proto_gre,nf_conntrack_netlink,nf_conntrack_netbios_ns,nf_conntrack_irc,nf_conntrack_h323,nf_conntrack_ftp,xt_helper,xt_conntrack,xt_CONNMARK,xt_connmark,xt_state,iptable_nat,nf_nat,nf_conntrack_ipv4
iptable_mangle 2803 1
nfnetlink 3266 2 nf_conntrack_netlink,nfnetlink_log
iptable_filter 2271 1
ip_tables 9891 4 iptable_raw,iptable_nat,iptable_mangle,iptable_filter
x_tables 14299 48 ipt_IFWLOG,ipt_psd,xt_time,xt_connlimit,xt_realm,xt_comment,xt_recent,xt_policy,ipt_ULOG,ipt_REJECT,ipt_REDIRECT,ipt_NETMAP,ipt_MASQUERADE,ipt_ECN,ipt_ecn,ipt_CLUSTERIP,ipt_ah,ipt_addrtype,ipt_set,ipt_SET,xt_TPROXY,xt_tcpmss,xt_pkttype,xt_physdev,xt_owner,xt_NFQUEUE,xt_NFLOG,xt_multiport,xt_MARK,xt_mark,xt_mac,xt_limit,xt_length,xt_iprange,xt_helper,xt_hashlimit,xt_DSCP,xt_dscp,xt_dccp,xt_conntrack,xt_CONNMARK,xt_connmark,xt_CLASSIFY,ipt_LOG,xt_tcpudp,xt_state,iptable_nat,ip_tables
nfsd 237383 13
exportfs 3341 1 nfsd
nfs 266295 0
lockd 64732 2 nfsd,nfs
fscache 53686 1 nfs
nfs_acl 2245 2 nfsd,nfs
auth_rpcgss 32964 2 nfsd,nfs
sunrpc 191517 16 nfsd,nfs,lockd,nfs_acl,auth_rpcgss
nls_iso8859_1 3249 1
nls_cp437 4919 1
vfat 8513 1
fat 47218 1 vfat
af_packet 15914 2
ipv6 265413 34
snd_hda_codec_realtek 219464 1
snd_hda_intel 22717 2
snd_hda_codec 79871 2 snd_hda_codec_realtek,snd_hda_intel
snd_hwdep 5700 1 snd_hda_codec
snd_seq_dummy 1370 0
snd_seq_oss 30465 0
snd_seq_midi_event 6003 1 snd_seq_oss
snd_seq 50859 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
snd_seq_device 6084 3 snd_seq_dummy,snd_seq_oss,snd_seq
snd_pcm_oss 41415 0
snd_pcm 76689 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss
snd_timer 18943 2 snd_seq,snd_pcm
snd_mixer_oss 14278 1 snd_pcm_oss
snd 57638 16 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_seq_dummy,snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_pcm,snd_timer,snd_mixer_oss
soundcore 6619 1 snd
jmb38x_ms 11242 0
serio_raw 4073 0
sdhci_pci 6322 0
sdhci 17689 1 sdhci_pci
mmc_core 62556 1 sdhci
sr_mod 13814 0
snd_page_alloc 7108 2 snd_hda_intel,snd_pcm
sis190 14282 0
mii 4381 1 sis190
memstick 9035 1 jmb38x_ms
binfmt_misc 6369 1
fuse 56418 6
sg 25341 0
nvidia 9381900 44
cpufreq_ondemand 8082 2
cpufreq_conservative 9394 0
cpufreq_powersave 754 0
acpi_cpufreq 6293 0
arc4 1153 2
uvcvideo 56497 0
videodev 36601 1 uvcvideo
v4l1_compat 13315 2 uvcvideo,videodev
ecb 1679 2
i2c_core 24741 2 nvidia,videodev
freq_table 3383 2 cpufreq_ondemand,acpi_cpufreq
rtl8187 48886 0
mac80211 165049 1 rtl8187
usb_storage 40343 1
led_class 2832 2 sdhci,rtl8187
cfg80211 122795 2 rtl8187,mac80211
rfkill 15794 1 cfg80211
eeprom_93cx6 1333 1 rtl8187
nvram 6076 0
ehci_hcd 46369 0
ohci_hcd 29401 0
video 17149 0
usbcore 176556 6 uvcvideo,rtl8187,usb_storage,ehci_hcd,ohci_hcd
output 1871 1 video
thermal 10871 0
dm_mod 62953 0
processor 30045 3 acpi_cpufreq
battery 8220 0
button 4709 0
ac 2638 0
wmi 6633 0
joydev 8423 0
evdev 7403 14
ata_generic 2551 0
ide_pci_generic 2430 0
ide_gd_mod 23741 0
ide_core 98019 2 ide_pci_generic,ide_gd_mod
pata_acpi 2579 0
sata_sis 3364 3
pata_sis 8725 1 sata_sis
libata 168593 4 ata_generic,pata_acpi,sata_sis,pata_sis
sd_mod 33309 6
scsi_mod 146689 5 sr_mod,sg,usb_storage,libata,sd_mod
crc_t10dif 1251 1 sd_mod
ext4 320503 1
jbd2 71640 1 ext4
crc16 1339 1 ext4
[/console]

[console]
DEVICE=wlan0
BOOTPROTO=dhcp
ONBOOT=yes
METRIC=35
MII_NOT_SUPPORTED=no
USERCTL=yes
RESOLV_MODS=no
WIRELESS_MODE=Managed
WIRELESS_ESSID="TPU Public"
WIRELESS_ENC_KEY=s:
WIRELESS_WPA_DRIVER=wext
WIRELESS_WPA_REASSOCIATE=no
IPV6INIT=yes
IPV6TO4INIT=yes
ACCOUNTING=yes
DHCP_CLIENT=dhclient
DHCP_HOSTNAME=TPU
NEEDHOSTNAME=yes
PEERDNS=yes
PEERYP=yes
PEERNTPD=no
[/console]

[console]
##### Example wpa_supplicant configuration file ###############################
#
# This file describes configuration file format and lists all available option.
# Please also take a look at simpler configuration examples in 'examples'
# subdirectory.
#
# Empty lines and lines starting with # are ignored

# NOTE! This file may contain password information and should probably be made
# readable only by root user on multiuser systems.

# Note: All file paths in this configuration file should use full (absolute,
# not relative to working directory) path in order to allow working directory
# to be changed. This can happen if wpa_supplicant is run in the background.

# Whether to allow wpa_supplicant to update (overwrite) configuration
#
# This option can be used to allow wpa_supplicant to overwrite configuration
# file whenever configuration is changed (e.g., new network block is added with
# wpa_cli or wpa_gui, or a password is changed). This is required for
# wpa_cli/wpa_gui to be able to store the configuration changes permanently.
# Please note that overwriting configuration file will remove the comments from
# it.
#update_config=1

# global configuration (shared by all network blocks)
#
# Parameters for the control interface. If this is specified, wpa_supplicant
# will open a control interface that is available for external programs to
# manage wpa_supplicant. The meaning of this string depends on which control
# interface mechanism is used. For all cases, the existance of this parameter
# in configuration is used to determine whether the control interface is
# enabled.
#
# For UNIX domain sockets (default on Linux and BSD): This is a directory that
# will be created for UNIX domain sockets for listening to requests from
# external programs (CLI/GUI, etc.) for status information and configuration.
# The socket file will be named based on the interface name, so multiple
# wpa_supplicant processes can be run at the same time if more than one
# interface is used.
# /var/run/wpa_supplicant is the recommended directory for sockets and by
# default, wpa_cli will use it when trying to connect with wpa_supplicant.
#
# Access control for the control interface can be configured by setting the
# directory to allow only members of a group to use sockets. This way, it is
# possible to run wpa_supplicant as root (since it needs to change network
# configuration and open raw sockets) and still allow GUI/CLI components to be
# run as non-root users. However, since the control interface can be used to
# change the network configuration, this access needs to be protected in many
# cases. By default, wpa_supplicant is configured to use gid 0 (root). If you
# want to allow non-root users to use the control interface, add a new group
# and change this value to match with that group. Add users that should have
# control interface access to this group. If this variable is commented out or
# not included in the configuration file, group will not be changed from the
# value it got by default when the directory or socket was created.
#
# When configuring both the directory and group, use following format:
# DIR=/var/run/wpa_supplicant GROUP=wheel
# DIR=/var/run/wpa_supplicant GROUP=0
# (group can be either group name or gid)
#
# For UDP connections (default on Windows): The value will be ignored. This
# variable is just used to select that the control interface is to be created.
# The value can be set to, e.g., udp (ctrl_interface=udp)
#
# For Windows Named Pipe: This value can be used to set the security descriptor
# for controlling access to the control interface. Security descriptor can be
# set using Security Descriptor String Format (see http://msdn.microsoft.com/
# library/default.asp?url=/library/en-us/secauthz/security/
# security_descriptor_string_format.asp). The descriptor string needs to be
# prefixed with SDDL=. For example, ctrl_interface=SDDL=D: would set an empty
# DACL (which will reject all connections). See README-Windows.txt for more
# information about SDDL string format.
#
ctrl_interface=/var/run/wpa_supplicant

# IEEE 802.1X/EAPOL version
# wpa_supplicant is implemented based on IEEE Std 802.1X-2004 which defines
# EAPOL version 2. However, there are many APs that do not handle the new
# version number correctly (they seem to drop the frames completely). In order
# to make wpa_supplicant interoperate with these APs, the version number is set
# to 1 by default. This configuration value can be used to set it to the new
# version (2).
eapol_version=1

# AP scanning/selection
# By default, wpa_supplicant requests driver to perform AP scanning and then
# uses the scan results to select a suitable AP. Another alternative is to
# allow the driver to take care of AP scanning and selection and use
# wpa_supplicant just to process EAPOL frames based on IEEE 802.11 association
# information from the driver.
# 1: wpa_supplicant initiates scanning and AP selection
# 0: driver takes care of scanning, AP selection, and IEEE 802.11 association
# parameters (e.g., WPA IE generation); this mode can also be used with
# non-WPA drivers when using IEEE 802.1X mode; do not try to associate with
# APs (i.e., external program needs to control association). This mode must
# also be used when using wired Ethernet drivers.
# 2: like 0, but associate with APs using security policy and SSID (but not
# BSSID); this can be used, e.g., with ndiswrapper and NDIS drivers to
# enable operation with hidden SSIDs and optimized roaming; in this mode,
# the network blocks in the configuration file are tried one by one until
# the driver reports successful association; each network block should have
# explicit security policy (i.e., only one option in the lists) for
# key_mgmt, pairwise, group, proto variables
ap_scan=1

# EAP fast re-authentication
# By default, fast re-authentication is enabled for all EAP methods that
# support it. This variable can be used to disable fast re-authentication.
# Normally, there is no need to disable this.
fast_reauth=1

# OpenSSL Engine support
# These options can be used to load OpenSSL engines.
# The two engines that are supported currently are shown below:
# They are both from the opensc project (http://www.opensc.org/)
# By default no engines are loaded.
# make the opensc engine available
#opensc_engine_path=/usr/lib/opensc/engine_opensc.so
# make the pkcs11 engine available
#pkcs11_engine_path=/usr/lib/opensc/engine_pkcs11.so
# configure the path to the pkcs11 module required by the pkcs11 engine
#pkcs11_module_path=/usr/lib/pkcs11/opensc-pkcs11.so

# Dynamic EAP methods
# If EAP methods were built dynamically as shared object files, they need to be
# loaded here before being used in the network blocks. By default, EAP methods
# are included statically in the build, so these lines are not needed
#load_dynamic_eap=/usr/lib/wpa_supplicant/eap_tls.so
#load_dynamic_eap=/usr/lib/wpa_supplicant/eap_md5.so

# Driver interface parameters
# This field can be used to configure arbitrary driver interace parameters. The
# format is specific to the selected driver interface. This field is not used
# in most cases.
#driver_param="field=value"

# Country code
# The ISO/IEC alpha2 country code for the country in which this device is
# currently operating.
#country=US

# Maximum lifetime for PMKSA in seconds; default 43200
#dot11RSNAConfigPMKLifetime=43200
# Threshold for reauthentication (percentage of PMK lifetime); default 70
#dot11RSNAConfigPMKReauthThreshold=70
# Timeout for security association negotiation in seconds; default 60
#dot11RSNAConfigSATimeout=60

# Wi-Fi Protected Setup (WPS) parameters

# Universally Unique IDentifier (UUID; see RFC 4122) of the device
# If not configured, UUID will be generated based on the local MAC address.
#uuid=12345678-9abc-def0-1234-56789abcdef0

# Device Name
# User-friendly description of device; up to 32 octets encoded in UTF-8
#device_name=Wireless Client

# Manufacturer
# The manufacturer of the device (up to 64 ASCII characters)
#manufacturer=Company

# Model Name
# Model of the device (up to 32 ASCII characters)
#model_name=cmodel

# Model Number
# Additional device description (up to 32 ASCII characters)
#model_number=123

# Serial Number
# Serial number of the device (up to 32 characters)
#serial_number=12345

# Primary Device Type
# Used format: <categ>-<OUI>-<subcateg>
# categ = Category as an integer value
# OUI = OUI and type octet as a 4-octet hex-encoded value; 0050F204 for
# default WPS OUI
# subcateg = OUI-specific Sub Category as an integer value
# Examples:
# 1-0050F204-1 (Computer / PC)
# 1-0050F204-2 (Computer / Server)
# 5-0050F204-1 (Storage / NAS)
# 6-0050F204-1 (Network Infrastructure / AP)
#device_type=1-0050F204-1

# OS Version
# 4-octet operating system version number (hex string)
#os_version=01020300

# Credential processing
# 0 = process received credentials internally (default)
# 1 = do not process received credentials; just pass them over ctrl_iface to
# external program(s)
# 2 = process received credentials internally and pass them over ctrl_iface
# to external program(s)
#wps_cred_processing=0

# network block
#
# Each network (usually AP's sharing the same SSID) is configured as a separate
# block in this configuration file. The network blocks are in preference order
# (the first match is used).
#
# network block fields:
#
# disabled:
# 0 = this network can be used (default)
# 1 = this network block is disabled (can be enabled through ctrl_iface,
# e.g., with wpa_cli or wpa_gui)
#
# id_str: Network identifier string for external scripts. This value is passed
# to external action script through wpa_cli as WPA_ID_STR environment
# variable to make it easier to do network specific configuration.
#
# ssid: SSID (mandatory); either as an ASCII string with double quotation or
# as hex string; network name
#
# scan_ssid:
# 0 = do not scan this SSID with specific Probe Request frames (default)
# 1 = scan with SSID-specific Probe Request frames (this can be used to
# find APs that do not accept broadcast SSID or use multiple SSIDs;
# this will add latency to scanning, so enable this only when needed)
#
# bssid: BSSID (optional); if set, this network block is used only when
# associating with the AP using the configured BSSID
#
# priority: priority group (integer)
# By default, all networks will get same priority group (0). If some of the
# networks are more desirable, this field can be used to change the order in
# which wpa_supplicant goes through the networks when selecting a BSS. The
# priority groups will be iterated in decreasing priority (i.e., the larger the
# priority value, the sooner the network is matched against the scan results).
# Within each priority group, networks will be selected based on security
# policy, signal strength, etc.
# Please note that AP scanning with scan_ssid=1 and ap_scan=2 mode are not
# using this priority to select the order for scanning. Instead, they try the
# networks in the order that used in the configuration file.
#
# mode: IEEE 802.11 operation mode
# 0 = infrastructure (Managed) mode, i.e., associate with an AP (default)
# 1 = IBSS (ad-hoc, peer-to-peer)
# Note: IBSS can only be used with key_mgmt NONE (plaintext and static WEP)
# and key_mgmt=WPA-NONE (fixed group key TKIP/CCMP). In addition, ap_scan has
# to be set to 2 for IBSS. WPA-None requires following network block options:
# proto=WPA, key_mgmt=WPA-NONE, pairwise=NONE, group=TKIP (or CCMP, but not
# both), and psk must also be set.
#
# frequency: Channel frequency in megahertz (MHz) for IBSS, e.g.,
# 2412 = IEEE 802.11b/g channel 1. This value is used to configure the initial
# channel for IBSS (adhoc) networks. It is ignored in the infrastructure mode.
# In addition, this value is only used by the station that creates the IBSS. If
# an IBSS network with the configured SSID is already present, the frequency of
# the network will be used instead of this configured value.
#
# proto: list of accepted protocols
# WPA = WPA/IEEE 802.11i/D3.0
# RSN = WPA2/IEEE 802.11i (also WPA2 can be used as an alias for RSN)
# If not set, this defaults to: WPA RSN
#
# key_mgmt: list of accepted authenticated key management protocols
# WPA-PSK = WPA pre-shared key (this requires 'psk' field)
# WPA-EAP = WPA using EAP authentication
# IEEE8021X = IEEE 802.1X using EAP authentication and (optionally) dynamically
# generated WEP keys
# NONE = WPA is not used; plaintext or static WEP could be used
# WPA-PSK-SHA256 = Like WPA-PSK but using stronger SHA256-based algorithms
# WPA-EAP-SHA256 = Like WPA-EAP but using stronger SHA256-based algorithms
# If not set, this defaults to: WPA-PSK WPA-EAP
#
# auth_alg: list of allowed IEEE 802.11 authentication algorithms
# OPEN = Open System authentication (required for WPA/WPA2)
# SHARED = Shared Key authentication (requires static WEP keys)
# LEAP = LEAP/Network EAP (only used with LEAP)
# If not set, automatic selection is used (Open System with LEAP enabled if
# LEAP is allowed as one of the EAP methods).
#
# pairwise: list of accepted pairwise (unicast) ciphers for WPA
# CCMP = AES in Counter mode with CBC-MAC [RFC 3610, IEEE 802.11i/D7.0]
# TKIP = Temporal Key Integrity Protocol [IEEE 802.11i/D7.0]
# NONE = Use only Group Keys (deprecated, should not be included if APs support
# pairwise keys)
# If not set, this defaults to: CCMP TKIP
#
# group: list of accepted group (broadcast/multicast) ciphers for WPA
# CCMP = AES in Counter mode with CBC-MAC [RFC 3610, IEEE 802.11i/D7.0]
# TKIP = Temporal Key Integrity Protocol [IEEE 802.11i/D7.0]
# WEP104 = WEP (Wired Equivalent Privacy) with 104-bit key
# WEP40 = WEP (Wired Equivalent Privacy) with 40-bit key [IEEE 802.11]
# If not set, this defaults to: CCMP TKIP WEP104 WEP40
#
# psk: WPA preshared key; 256-bit pre-shared key
# The key used in WPA-PSK mode can be entered either as 64 hex-digits, i.e.,
# 32 bytes or as an ASCII passphrase (in which case, the real PSK will be
# generated using the passphrase and SSID). ASCII passphrase must be between
# 8 and 63 characters (inclusive).
# This field is not needed, if WPA-EAP is used.
# Note: Separate tool, wpa_passphrase, can be used to generate 256-bit keys
# from ASCII passphrase. This process uses lot of CPU and wpa_supplicant
# startup and reconfiguration time can be optimized by generating the PSK only
# only when the passphrase or SSID has actually changed.
#
# eapol_flags: IEEE 802.1X/EAPOL options (bit field)
# Dynamic WEP key required for non-WPA mode
# bit0 (1): require dynamically generated unicast WEP key
# bit1 (2): require dynamically generated broadcast WEP key
# (3 = require both keys; default)
# Note: When using wired authentication, eapol_flags must be set to 0 for the
# authentication to be completed successfully.
#
# mixed_cell: This option can be used to configure whether so called mixed
# cells, i.e., networks that use both plaintext and encryption in the same
# SSID, are allowed when selecting a BSS form scan results.
# 0 = disabled (default)
# 1 = enabled
#
# proactive_key_caching:
# Enable/disable opportunistic PMKSA caching for WPA2.
# 0 = disabled (default)
# 1 = enabled
#
# wep_key0..3: Static WEP key (ASCII in double quotation, e.g. "abcde" or
# hex without quotation, e.g., 0102030405)
# wep_tx_keyidx: Default WEP key index (TX) (0..3)
#
# peerkey: Whether PeerKey negotiation for direct links (IEEE 802.11e DLS) is
# allowed. This is only used with RSN/WPA2.
# 0 = disabled (default)
# 1 = enabled
#peerkey=1
#
# wpa_ptk_rekey: Maximum lifetime for PTK in seconds. This can be used to
# enforce rekeying of PTK to mitigate some attacks against TKIP deficiencies.
#
# Following fields are only used with internal EAP implementation.
# eap: space-separated list of accepted EAP methods
# MD5 = EAP-MD5 (unsecure and does not generate keying material ->
# cannot be used with WPA; to be used as a Phase 2 method
# with EAP-PEAP or EAP-TTLS)
# MSCHAPV2 = EAP-MSCHAPv2 (cannot be used separately with WPA; to be used
# as a Phase 2 method with EAP-PEAP or EAP-TTLS)
# OTP = EAP-OTP (cannot be used separately with WPA; to be used
# as a Phase 2 method with EAP-PEAP or EAP-TTLS)
# GTC = EAP-GTC (cannot be used separately with WPA; to be used
# as a Phase 2 method with EAP-PEAP or EAP-TTLS)
# TLS = EAP-TLS (client and server certificate)
# PEAP = EAP-PEAP (with tunnelled EAP authentication)
# TTLS = EAP-TTLS (with tunnelled EAP or PAP/CHAP/MSCHAP/MSCHAPV2
# authentication)
# If not set, all compiled in methods are allowed.
#
# identity: Identity string for EAP
# This field is also used to configure user NAI for
# EAP-PSK/PAX/SAKE/GPSK.
# anonymous_identity: Anonymous identity string for EAP (to be used as the
# unencrypted identity with EAP types that support different tunnelled
# identity, e.g., EAP-TTLS)
# password: Password string for EAP. This field can include either the
# plaintext password (using ASCII or hex string) or a NtPasswordHash
# (16-byte MD4 hash of password) in hash:<32 hex digits> format.
# NtPasswordHash can only be used when the password is for MSCHAPv2 or
# MSCHAP (EAP-MSCHAPv2, EAP-TTLS/MSCHAPv2, EAP-TTLS/MSCHAP, LEAP).
# EAP-PSK (128-bit PSK), EAP-PAX (128-bit PSK), and EAP-SAKE (256-bit
# PSK) is also configured using this field. For EAP-GPSK, this is a
# variable length PSK.
# ca_cert: File path to CA certificate file (PEM/DER). This file can have one
# or more trusted CA certificates. If ca_cert and ca_path are not
# included, server certificate will not be verified. This is insecure and
# a trusted CA certificate should always be configured when using
# EAP-TLS/TTLS/PEAP. Full path should be used since working directory may
# change when wpa_supplicant is run in the background.
# On Windows, trusted CA certificates can be loaded from the system
# certificate store by setting this to cert_store://<name>, e.g.,
# ca_cert="cert_store://CA" or ca_cert="cert_store://ROOT".
# Note that when running wpa_supplicant as an application, the user
# certificate store (My user account) is used, whereas computer store
# (Computer account) is used when running wpasvc as a service.
# ca_path: Directory path for CA certificate files (PEM). This path may
# contain multiple CA certificates in OpenSSL format. Common use for this
# is to point to system trusted CA list which is often installed into
# directory like /etc/ssl/certs. If configured, these certificates are
# added to the list of trusted CAs. ca_cert may also be included in that
# case, but it is not required.
# client_cert: File path to client certificate file (PEM/DER)
# Full path should be used since working directory may change when
# wpa_supplicant is run in the background.
# Alternatively, a named configuration blob can be used by setting this
# to blob://<blob name>.
# private_key: File path to client private key file (PEM/DER/PFX)
# When PKCS#12/PFX file (.p12/.pfx) is used, client_cert should be
# commented out. Both the private key and certificate will be read from
# the PKCS#12 file in this case. Full path should be used since working
# directory may change when wpa_supplicant is run in the background.
# Windows certificate store can be used by leaving client_cert out and
# configuring private_key in one of the following formats:
# cert://substring_to_match
# hash://certificate_thumbprint_in_hex
# for example: private_key="hash://63093aa9c47f56ae88334c7b65a4"
# Note that when running wpa_supplicant as an application, the user
# certificate store (My user account) is used, whereas computer store
# (Computer account) is used when running wpasvc as a service.
# Alternatively, a named configuration blob can be used by setting this
# to blob://<blob name>.
# private_key_passwd: Password for private key file (if left out, this will be
# asked through control interface)
# dh_file: File path to DH/DSA parameters file (in PEM format)
# This is an optional configuration file for setting parameters for an
# ephemeral DH key exchange. In most cases, the default RSA
# authentication does not use this configuration. However, it is possible
# setup RSA to use ephemeral DH key exchange. In addition, ciphers with
# DSA keys always use ephemeral DH keys. This can be used to achieve
# forward secrecy. If the file is in DSA parameters format, it will be
# automatically converted into DH params.
# subject_match: Substring to be matched against the subject of the
# authentication server certificate. If this string is set, the server
# sertificate is only accepted if it contains this string in the subject.
# The subject string is in following format:
# /C=US/ST=CA/L=San Francisco/CN=Test AS/emailAddress=as@example.com
# altsubject_match: Semicolon separated string of entries to be matched against
# the alternative subject name of the authentication server certificate.
# If this string is set, the server sertificate is only accepted if it
# contains one of the entries in an alternative subject name extension.
# altSubjectName string is in following format: TYPE:VALUE
# Example: EMAIL:server@example.com
# Example: DNS:server.example.com;DNS:server2.example.com
# Following types are supported: EMAIL, DNS, URI
# phase1: Phase1 (outer authentication, i.e., TLS tunnel) parameters
# (string with field-value pairs, e.g., "peapver=0" or
# "peapver=1 peaplabel=1")
# 'peapver' can be used to force which PEAP version (0 or 1) is used.
# 'peaplabel=1' can be used to force new label, "client PEAP encryption",
# to be used during key derivation when PEAPv1 or newer. Most existing
# PEAPv1 implementation seem to be using the old label, "client EAP
# encryption", and wpa_supplicant is now using that as the default value.
# Some servers, e.g., Radiator, may require peaplabel=1 configuration to
# interoperate with PEAPv1; see eap_testing.txt for more details.
# 'peap_outer_success=0' can be used to terminate PEAP authentication on
# tunneled EAP-Success. This is required with some RADIUS servers that
# implement draft-josefsson-pppext-eap-tls-eap-05.txt (e.g.,
# Lucent NavisRadius v4.4.0 with PEAP in "IETF Draft 5" mode)
# include_tls_length=1 can be used to force wpa_supplicant to include
# TLS Message Length field in all TLS messages even if they are not
# fragmented.
# sim_min_num_chal=3 can be used to configure EAP-SIM to require three
# challenges (by default, it accepts 2 or 3)
# result_ind=1 can be used to enable EAP-SIM and EAP-AKA to use
# protected result indication.
# 'crypto_binding' option can be used to control PEAPv0 cryptobinding
# behavior:
# * 0 = do not use cryptobinding (default)
# * 1 = use cryptobinding if server supports it
# * 2 = require cryptobinding
# EAP-WSC (WPS) uses following options: pin=<Device Password> or
# pbc=1.
# phase2: Phase2 (inner authentication with TLS tunnel) parameters
# (string with field-value pairs, e.g., "auth=MSCHAPV2" for EAP-PEAP or
# "autheap=MSCHAPV2 autheap=MD5" for EAP-TTLS)
# Following certificate/private key fields are used in inner Phase2
# authentication when using EAP-TTLS or EAP-PEAP.
# ca_cert2: File path to CA certificate file. This file can have one or more
# trusted CA certificates. If ca_cert2 and ca_path2 are not included,
# server certificate will not be verified. This is insecure and a trusted
# CA certificate should always be configured.
# ca_path2: Directory path for CA certificate files (PEM)
# client_cert2: File path to client certificate file
# private_key2: File path to client private key file
# private_key2_passwd: Password for private key file
# dh_file2: File path to DH/DSA parameters file (in PEM format)
# subject_match2: Substring to be matched against the subject of the
# authentication server certificate.
# altsubject_match2: Substring to be matched against the alternative subject
# name of the authentication server certificate.
#
# fragment_size: Maximum EAP fragment size in bytes (default 1398).
# This value limits the fragment size for EAP methods that support
# fragmentation (e.g., EAP-TLS and EAP-PEAP). This value should be set
# small enough to make the EAP messages fit in MTU of the network
# interface used for EAPOL. The default value is suitable for most
# cases.
#
# EAP-FAST variables:
# pac_file: File path for the PAC entries. wpa_supplicant will need to be able
# to create this file and write updates to it when PAC is being
# provisioned or refreshed. Full path to the file should be used since
# working directory may change when wpa_supplicant is run in the
# background. Alternatively, a named configuration blob can be used by
# setting this to blob://<blob name>
# phase1: fast_provisioning option can be used to enable in-line provisioning
# of EAP-FAST credentials (PAC):
# 0 = disabled,
# 1 = allow unauthenticated provisioning,
# 2 = allow authenticated provisioning,
# 3 = allow both unauthenticated and authenticated provisioning
# fast_max_pac_list_len=<num> option can be used to set the maximum
# number of PAC entries to store in a PAC list (default: 10)
# fast_pac_format=binary option can be used to select binary format for
# storing PAC entries in order to save some space (the default
# text format uses about 2.5 times the size of minimal binary
# format)
#
# wpa_supplicant supports number of "EAP workarounds" to work around
# interoperability issues with incorrectly behaving authentication servers.
# These are enabled by default because some of the issues are present in large
# number of authentication servers. Strict EAP conformance mode can be
# configured by disabling workarounds with eap_workaround=0.

# Example blocks:

# Simple case: WPA-PSK, PSK as an ASCII passphrase, allow all valid ciphers
# network={
# ssid="simple"
# psk="very secret passphrase"
# priority=5
# }

# Same as previous, but request SSID-specific scanning (for APs that reject
# broadcast SSID)
# network={
# ssid="second ssid"
# scan_ssid=1
# psk="very secret passphrase"
# priority=2
# }

# Only WPA-PSK is used. Any valid cipher combination is accepted.
# network={
# ssid="example"
# proto=WPA
# key_mgmt=WPA-PSK
# pairwise=CCMP TKIP
# group=CCMP TKIP WEP104 WEP40
# psk=06b4be19da289f475aa46a33cb793029d4ab3db7a23ee92382eb0106c72ac7bb
# priority=2
# }

# WPA-Personal(PSK) with TKIP and enforcement for frequent PTK rekeying
# network={
# ssid="example"
# proto=WPA
# key_mgmt=WPA-PSK
# pairwise=TKIP
# group=TKIP
# psk="not so secure passphrase"
# wpa_ptk_rekey=600
# }

# Only WPA-EAP is used. Both CCMP and TKIP is accepted. An AP that used WEP104
# or WEP40 as the group cipher will not be accepted.
# network={
# ssid="example"
# proto=RSN
# key_mgmt=WPA-EAP
# pairwise=CCMP TKIP
# group=CCMP TKIP
# eap=TLS
# identity="user@example.com"
# ca_cert="/etc/cert/ca.pem"
# client_cert="/etc/cert/user.pem"
# private_key="/etc/cert/user.prv"
# private_key_passwd="password"
# priority=1
# }

# EAP-PEAP/MSCHAPv2 configuration for RADIUS servers that use the new peaplabel
# (e.g., Radiator)
# network={
# ssid="example"
# key_mgmt=WPA-EAP
# eap=PEAP
# identity="user@example.com"
# password="foobar"
# ca_cert="/etc/cert/ca.pem"
# phase1="peaplabel=1"
# phase2="auth=MSCHAPV2"
# priority=10
# }

# EAP-TTLS/EAP-MD5-Challenge configuration with anonymous identity for the
# unencrypted use. Real identity is sent only within an encrypted TLS tunnel.
# network={
# ssid="example"
# key_mgmt=WPA-EAP
# eap=TTLS
# identity="user@example.com"
# anonymous_identity="anonymous@example.com"
# password="foobar"
# ca_cert="/etc/cert/ca.pem"
# priority=2
# }

# EAP-TTLS/MSCHAPv2 configuration with anonymous identity for the unencrypted
# use. Real identity is sent only within an encrypted TLS tunnel.
# network={
# ssid="example"
# key_mgmt=WPA-EAP
# eap=TTLS
# identity="user@example.com"
# anonymous_identity="anonymous@example.com"
# password="foobar"
# ca_cert="/etc/cert/ca.pem"
# phase2="auth=MSCHAPV2"
# }

# WPA-EAP, EAP-TTLS with different CA certificate used for outer and inner
# authentication.
# network={
# ssid="example"
# key_mgmt=WPA-EAP
# eap=TTLS
# # Phase1 / outer authentication
# anonymous_identity="anonymous@example.com"
# ca_cert="/etc/cert/ca.pem"
# # Phase 2 / inner authentication
# phase2="autheap=TLS"
# ca_cert2="/etc/cert/ca2.pem"
# client_cert2="/etc/cer/user.pem"
# private_key2="/etc/cer/user.prv"
# private_key2_passwd="password"
# priority=2
# }

# Both WPA-PSK and WPA-EAP is accepted. Only CCMP is accepted as pairwise and
# group cipher.
# network={
# ssid="example"
# bssid=00:11:22:33:44:55
# proto=WPA RSN
# key_mgmt=WPA-PSK WPA-EAP
# pairwise=CCMP
# group=CCMP
# psk=06b4be19da289f475aa46a33cb793029d4ab3db7a23ee92382eb0106c72ac7bb
# }

# Special characters in SSID, so use hex string. Default to WPA-PSK, WPA-EAP
# and all valid ciphers.
# network={
# ssid=00010203
# psk=000102030405060708090a0b0c0d0e0f101112131415161718191a1b1c1d1e1f
# }


# EAP-SIM with a GSM SIM or USIM
# network={
# ssid="eap-sim-test"
# key_mgmt=WPA-EAP
# eap=SIM
# pin="1234"
# pcsc=""
# }


# EAP-PSK
# network={
# ssid="eap-psk-test"
# key_mgmt=WPA-EAP
# eap=PSK
# anonymous_identity="eap_psk_user"
# password=06b4be19da289f475aa46a33cb793029
# identity="eap_psk_user@example.com"
# }


# IEEE 802.1X/EAPOL with dynamically generated WEP keys (i.e., no WPA) using
# EAP-TLS for authentication and key generation; require both unicast and
# broadcast WEP keys.
# network={
# ssid="1x-test"
# key_mgmt=IEEE8021X
# eap=TLS
# identity="user@example.com"
# ca_cert="/etc/cert/ca.pem"
# client_cert="/etc/cert/user.pem"
# private_key="/etc/cert/user.prv"
# private_key_passwd="password"
# eapol_flags=3
# }


# LEAP with dynamic WEP keys
# network={
# ssid="leap-example"
# key_mgmt=IEEE8021X
# eap=LEAP
# identity="user"
# password="foobar"
# }

# EAP-IKEv2 using shared secrets for both server and peer authentication
# network={
# ssid="ikev2-example"
# key_mgmt=WPA-EAP
# eap=IKEV2
# identity="user"
# password="foobar"
# }

# EAP-FAST with WPA (WPA or WPA2)
# network={
# ssid="eap-fast-test"
# key_mgmt=WPA-EAP
# eap=FAST
# anonymous_identity="FAST-000102030405"
# identity="username"
# password="password"
# phase1="fast_provisioning=1"
# pac_file="/etc/wpa_supplicant.eap-fast-pac"
# }

# network={
# ssid="eap-fast-test"
# key_mgmt=WPA-EAP
# eap=FAST
# anonymous_identity="FAST-000102030405"
# identity="username"
# password="password"
# phase1="fast_provisioning=1"
# pac_file="blob://eap-fast-pac"
# }

# Plaintext connection (no WPA, no IEEE 802.1X)
# network={
# ssid="plaintext-test"
# key_mgmt=NONE
# }


# Shared WEP key connection (no WPA, no IEEE 802.1X)
# network={
# ssid="static-wep-test"
# key_mgmt=NONE
# wep_key0="abcde"
# wep_key1=0102030405
# wep_key2="1234567890123"
# wep_tx_keyidx=0
# priority=5
# }


# Shared WEP key connection (no WPA, no IEEE 802.1X) using Shared Key
# IEEE 802.11 authentication
# network={
# ssid="static-wep-test2"
# key_mgmt=NONE
# wep_key0="abcde"
# wep_key1=0102030405
# wep_key2="1234567890123"
# wep_tx_keyidx=0
# priority=5
# auth_alg=SHARED
# }


# IBSS/ad-hoc network with WPA-None/TKIP.
# network={
# ssid="test adhoc"
# mode=1
# frequency=2412
# proto=WPA
# key_mgmt=WPA-NONE
# pairwise=NONE
# group=TKIP
# psk="secret passphrase"
# }


# Catch all example that allows more or less all configuration modes
# network={
# ssid="example"
# scan_ssid=1
# key_mgmt=WPA-EAP WPA-PSK IEEE8021X NONE
# pairwise=CCMP TKIP
# group=CCMP TKIP WEP104 WEP40
# psk="very secret passphrase"
# eap=TTLS PEAP TLS
# identity="user@example.com"
# password="foobar"
# ca_cert="/etc/cert/ca.pem"
# client_cert="/etc/cert/user.pem"
# private_key="/etc/cert/user.prv"
# private_key_passwd="password"
# phase1="peaplabel=0"
# }

# Example of EAP-TLS with smartcard (openssl engine)
# network={
# ssid="example"
# key_mgmt=WPA-EAP
# eap=TLS
# proto=RSN
# pairwise=CCMP TKIP
# group=CCMP TKIP
# identity="user@example.com"
# ca_cert="/etc/cert/ca.pem"
# client_cert="/etc/cert/user.pem"
#
# engine=1
#
# # The engine configured here must be available. Look at
# # OpenSSL engine support in the global section.
# # The key available through the engine must be the private key
# # matching the client certificate configured above.
#
# # use the opensc engine
# #engine_id="opensc"
# #key_id="45"
#
# # use the pkcs11 engine
# engine_id="pkcs11"
# key_id="id_45"
#
# # Optional PIN configuration; this can be left out and PIN will be
# # asked through the control interface
# pin="1234"
# }

# Example configuration showing how to use an inlined blob as a CA certificate
# data instead of using external file
# network={
# ssid="example"
# key_mgmt=WPA-EAP
# eap=TTLS
# identity="user@example.com"
# anonymous_identity="anonymous@example.com"
# password="foobar"
# ca_cert="blob://exampleblob"
# priority=20
# }

blob-base64-exampleblob={
SGVsbG8gV29ybGQhCg==
}


# Wildcard match for SSID (plaintext APs only). This example select any
# open AP regardless of its SSID.
# network={
# key_mgmt=NONE
# }

network={
key_mgmt=NONE
mode=0
ssid="TPU Public"
priority=1
auth_alg=OPEN
proto=RSN WPA
group=CCMP TKIP
pairwise=CCMP TKIP
scan_ssid=1
eap=PEAP
password="xxxxxx"
identity="xxxxxxxxx"
}

network={
key_mgmt=WPA-EAP IEEE8021X NONE
proto=WPA
eap=GTC
group=TKIP
scan_ssid=1
mode=0
ssid="dom"
pairwise=TKIP
}
[/console]