гуглил ничего толкового не нашел, пошарился по настройкам дебиана ничего не нашел.
в винде юзал спидфан. Причина того что ищю данную прогу, камп гудит очень сильно. oO
LinuxForum.Fans
Pегулятор скорости оборотов кулера в линуксе
Автор: Veliz
15 сообщений
9826 просмотров
поставьте пакет lm-sensors.
После этого запустите калибровщик кулеров командой
pwmconfig
(кулера могут остановиться на мгновение)
Программа задаст вам вопросы, на которые нужно ответить. После калибровки результаты сохраняться в файл /etc/fancontrol. Конфиг можно если что отредактировать вручную.
Для применения новых настроек необходимо запустить службу:
/sbin/fancontrol
This program will search your sensors for pulse width modulation (pwm)
controls, and test each one to see if it controls a fan on
your motherboard. Note that many motherboards do not have pwm
circuitry installed, even if your sensor chip supports pwm.
We will attempt to briefly stop each fan using the pwm controls.
The program will attempt to restore each fan to full speed
after testing. However, it is ** very important ** that you
physically verify that the fans have been to full speed
after the program has completed.
/usr/sbin/pwmconfig: There are no pwm-capable sensor modules installed
что-то я не понял:
1. установил сенсор
2.запустил и ничего
1.1. наверно нужно было настроить сенсор для начала, вот что высвечивает при вводе sensors в консоль:
text
k8temp-pci-00c3
Adapter: PCI adapter
Core0 Temp: +8.0°C
Core0 Temp: +13.0°C
Core1 Temp: +8.0°C
Core1 Temp: +18.0°C 2.1. нет ли каких-то зависимостей которые я не установил?
спасибо за помощь.
Для настройки сенсоров
[console]# sensors-detect [/console]
Возможно ещё нужно будет загрузить модули, которые он скажет...
использовал команду до этого не помогло :( выводит тоже самое что и при прошлом запуске пвмконфиг
(установил бубунту посмотреть на 10.10 а то видел только 9.04 :rolleyes: ))
тутпонятно~$ sensors
k8temp-pci-00c3
Adapter: PCI adapter
Core0 Temp: +19.0°C
Core0 Temp: +26.0°C
Core1 Temp: +18.0°C
Core1 Temp: +27.0°C
atk0110-acpi-0
Adapter: ACPI interface
Vcore Voltage: +1.39 V (min = +0.85 V, max = +1.60 V)
+3.3 Voltage: +3.36 V (min = +2.97 V, max = +3.63 V)
+5 Voltage: +5.07 V (min = +4.50 V, max = +5.50 V)
+12 Voltage: +11.92 V (min = +10.20 V, max = +13.80 V)
CPU FAN Speed: 3479 RPM (min = 600 RPM)
CHASSIS FAN Speed: 0 RPM (min = 800 RPM)
CPU Temperature: +43.0°C (high = +60.0°C, crit = +95.0°C)
MB Temperature: +34.0°C (high = +45.0°C, crit = +95.0°C)
termo@fedora:~$ sensors
k8temp-pci-00c3
Adapter: PCI adapter
Core0 Temp: +15.0°C
Core0 Temp: +10.0°C
Core1 Temp: +20.0°C
Core1 Temp: +17.0°C
it8716-isa-0290
Adapter: ISA adapter
in0: +1.22 V (min = +0.00 V, max = +4.08 V)
in1: +1.90 V (min = +0.00 V, max = +4.08 V)
in2: +3.33 V (min = +0.00 V, max = +4.08 V)
in3: +2.98 V (min = +0.00 V, max = +4.08 V)
in4: +3.02 V (min = +0.00 V, max = +4.08 V)
in5: +3.20 V (min = +0.00 V, max = +4.08 V)
in6: +1.15 V (min = +0.00 V, max = +4.08 V)
in7: +2.93 V (min = +0.00 V, max = +4.08 V)
Vbat: +2.90 V
fan1: 1683 RPM (min = 0 RPM) (процессора)
fan2: 761 RPM (min = 0 RPM) (задний на блоке)
temp1: +39.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor (проц)
temp2: +41.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor (видео)
temp3: +31.0°C (low = +127.0°C, high = +127.0°C) sensor = thermal diode (мать)
cpu0_vid: +1.200 V
Termo, sorry я смотрел ваш ответ и немного не понял( а точнее вообще ничего :( ) можете объяснить что я могу сделать чтобы найти свою ошибку в действиях. Ваши комментарии мне ничего не дали(
З.Ы. у меня очень сильно гудит кулер на процессоре.
еще бы он не гудел
CPU FAN Speed: 3479 RPM (min = 600 RPM)
давайте полное название материнки, процесса и кулера
и еще срок работы компьютера без чистки внутреннего пространства на предмет сбора пыли
ибо судя по нормальной температуре датчиков и бешенной работе кулера
либо он молотит из-за пыли либо из-за трех пинового разъема
я видел и хочу понизить скорость. это понятно( просто программа не запускается.
Показать
[console]sudo sensors-detect
[sudo] password for vel:
# sensors-detect revision 5818 (2010-01-18 17:22:07 +0100)
# System: System manufacturer System Product Name
# Board: ASUSTeK Computer INC. M2N-X Plus
This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.
Some south bridges, CPUs or memory controllers contain embedded sensors.
Do you want to scan for them? This is totally safe. (YES/no): y
Silicon Integrated Systems SIS5595... No
VIA VT82C686 Integrated Sensors... No
VIA VT8231 Integrated Sensors... No
AMD K8 thermal sensors... Success!
(driver `k8temp')
AMD Family 10h thermal sensors... No
AMD Family 11h thermal sensors... No
Intel Core family thermal sensor... No
Intel Atom thermal sensor... No
Intel AMB FB-DIMM thermal sensor... No
VIA C7 thermal sensor... No
VIA Nano thermal sensor... No
Some Super I/O chips contain embedded sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): y
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor'... No
Trying family `SMSC'... No
Trying family `VIA/Winbond/Nuvoton/Fintek'... No
Trying family `ITE'... Yes
Found `ITE IT8712F Super IO Sensors' Success!
(address 0x290, driver `it87')
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor'... No
Trying family `SMSC'... No
Trying family `VIA/Winbond/Nuvoton/Fintek'... No
Trying family `ITE'... No
Some systems (mainly servers) implement IPMI, a set of common interfaces
through which system health data may be retrieved, amongst other things.
We first try to get the information from SMBIOS. If we don't find it
there, we have to read from arbitrary I/O ports to probe for such
interfaces. This is normally safe. Do you want to scan for IPMI
interfaces? (YES/no): y
Probing for `IPMI BMC KCS' at 0xca0... No
Probing for `IPMI BMC SMIC' at 0xca8... No
Some hardware monitoring chips are accessible through the ISA I/O ports.
We have to write to arbitrary I/O ports to probe them. This is usually
safe though. Yes, you do have ISA I/O ports even if you do not have any
ISA slots! Do you want to scan the ISA I/O ports? (yes/NO): yy
Probing for `National Semiconductor LM78' at 0x290... No
Probing for `National Semiconductor LM79' at 0x290... No
Probing for `Winbond W83781D' at 0x290... No
Probing for `Winbond W83782D' at 0x290... No
Lastly, we can probe the I2C/SMBus adapters for connected hardware
monitoring devices. This is the most risky part, and while it works
reasonably well on most systems, it has been reported to cause trouble
on some systems.
Do you want to probe the I2C/SMBus adapters now? (YES/no): y
Using driver `i2c-nforce2' for device 0000:00:01.1: nVidia Corporation nForce SMBus (MCP61)
Module i2c-dev loaded successfully.
Next adapter: SMBus nForce2 adapter at 0600 (i2c-0)
Do you want to scan it? (YES/no/selectively): y
Client found at address 0x50
Probing for `Analog Devices ADM1033'... No
Probing for `Analog Devices ADM1034'... No
Probing for `SPD EEPROM'... Yes
(confidence 8, not a hardware monitoring chip)
Probing for `EDID EEPROM'... No
Client found at address 0x51
Probing for `Analog Devices ADM1033'... No
Probing for `Analog Devices ADM1034'... No
Probing for `SPD EEPROM'... Yes
(confidence 8, not a hardware monitoring chip)
Next adapter: SMBus nForce2 adapter at 0700 (i2c-1)
Do you want to scan it? (YES/no/selectively): y
Next adapter: NVIDIA i2c adapter (i2c-2)
Do you want to scan it? (YES/no/selectively): y
Next adapter: NVIDIA i2c adapter (i2c-3)
Do you want to scan it? (YES/no/selectively): y
Client found at address 0x50
Probing for `Analog Devices ADM1033'... No
Probing for `Analog Devices ADM1034'... No
Probing for `SPD EEPROM'... No
Probing for `EDID EEPROM'... Yes
(confidence 8, not a hardware monitoring chip)
Client found at address 0x51
Probing for `Analog Devices ADM1033'... No
Probing for `Analog Devices ADM1034'... No
Probing for `SPD EEPROM'... No
Client found at address 0x52
Probing for `Analog Devices ADM1033'... No
Probing for `Analog Devices ADM1034'... No
Probing for `SPD EEPROM'... No
Client found at address 0x53
Probing for `Analog Devices ADM1033'... No
Probing for `Analog Devices ADM1034'... No
Probing for `SPD EEPROM'... No
Next adapter: NVIDIA i2c adapter (i2c-4)
Do you want to scan it? (YES/no/selectively): y
Now follows a summary of the probes I have just done.
Just press ENTER to continue:
Driver `it87':
* ISA bus, address 0x290
Chip `ITE IT8712F Super IO Sensors' (confidence: 9)
Driver `k8temp' (autoloaded):
* Chip `AMD K8 thermal sensors' (confidence: 9)
To load everything that is needed, add this to /etc/modules:
#----cut here----
# Chip drivers
it87
#----cut here----
If you have some drivers built into your kernel, the list above will
contain too many modules. Skip the appropriate ones!
Do you want to add these lines automatically to /etc/modules? (yes/NO)y
Successful!
Monitoring programs won't work until the needed modules are
loaded. You may want to run '/etc/init.d/module-init-tools start'
to load them.
Unloading i2c-dev... OK
[/console]
[sudo] password for vel:
# sensors-detect revision 5818 (2010-01-18 17:22:07 +0100)
# System: System manufacturer System Product Name
# Board: ASUSTeK Computer INC. M2N-X Plus
This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.
Some south bridges, CPUs or memory controllers contain embedded sensors.
Do you want to scan for them? This is totally safe. (YES/no): y
Silicon Integrated Systems SIS5595... No
VIA VT82C686 Integrated Sensors... No
VIA VT8231 Integrated Sensors... No
AMD K8 thermal sensors... Success!
(driver `k8temp')
AMD Family 10h thermal sensors... No
AMD Family 11h thermal sensors... No
Intel Core family thermal sensor... No
Intel Atom thermal sensor... No
Intel AMB FB-DIMM thermal sensor... No
VIA C7 thermal sensor... No
VIA Nano thermal sensor... No
Some Super I/O chips contain embedded sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): y
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor'... No
Trying family `SMSC'... No
Trying family `VIA/Winbond/Nuvoton/Fintek'... No
Trying family `ITE'... Yes
Found `ITE IT8712F Super IO Sensors' Success!
(address 0x290, driver `it87')
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor'... No
Trying family `SMSC'... No
Trying family `VIA/Winbond/Nuvoton/Fintek'... No
Trying family `ITE'... No
Some systems (mainly servers) implement IPMI, a set of common interfaces
through which system health data may be retrieved, amongst other things.
We first try to get the information from SMBIOS. If we don't find it
there, we have to read from arbitrary I/O ports to probe for such
interfaces. This is normally safe. Do you want to scan for IPMI
interfaces? (YES/no): y
Probing for `IPMI BMC KCS' at 0xca0... No
Probing for `IPMI BMC SMIC' at 0xca8... No
Some hardware monitoring chips are accessible through the ISA I/O ports.
We have to write to arbitrary I/O ports to probe them. This is usually
safe though. Yes, you do have ISA I/O ports even if you do not have any
ISA slots! Do you want to scan the ISA I/O ports? (yes/NO): yy
Probing for `National Semiconductor LM78' at 0x290... No
Probing for `National Semiconductor LM79' at 0x290... No
Probing for `Winbond W83781D' at 0x290... No
Probing for `Winbond W83782D' at 0x290... No
Lastly, we can probe the I2C/SMBus adapters for connected hardware
monitoring devices. This is the most risky part, and while it works
reasonably well on most systems, it has been reported to cause trouble
on some systems.
Do you want to probe the I2C/SMBus adapters now? (YES/no): y
Using driver `i2c-nforce2' for device 0000:00:01.1: nVidia Corporation nForce SMBus (MCP61)
Module i2c-dev loaded successfully.
Next adapter: SMBus nForce2 adapter at 0600 (i2c-0)
Do you want to scan it? (YES/no/selectively): y
Client found at address 0x50
Probing for `Analog Devices ADM1033'... No
Probing for `Analog Devices ADM1034'... No
Probing for `SPD EEPROM'... Yes
(confidence 8, not a hardware monitoring chip)
Probing for `EDID EEPROM'... No
Client found at address 0x51
Probing for `Analog Devices ADM1033'... No
Probing for `Analog Devices ADM1034'... No
Probing for `SPD EEPROM'... Yes
(confidence 8, not a hardware monitoring chip)
Next adapter: SMBus nForce2 adapter at 0700 (i2c-1)
Do you want to scan it? (YES/no/selectively): y
Next adapter: NVIDIA i2c adapter (i2c-2)
Do you want to scan it? (YES/no/selectively): y
Next adapter: NVIDIA i2c adapter (i2c-3)
Do you want to scan it? (YES/no/selectively): y
Client found at address 0x50
Probing for `Analog Devices ADM1033'... No
Probing for `Analog Devices ADM1034'... No
Probing for `SPD EEPROM'... No
Probing for `EDID EEPROM'... Yes
(confidence 8, not a hardware monitoring chip)
Client found at address 0x51
Probing for `Analog Devices ADM1033'... No
Probing for `Analog Devices ADM1034'... No
Probing for `SPD EEPROM'... No
Client found at address 0x52
Probing for `Analog Devices ADM1033'... No
Probing for `Analog Devices ADM1034'... No
Probing for `SPD EEPROM'... No
Client found at address 0x53
Probing for `Analog Devices ADM1033'... No
Probing for `Analog Devices ADM1034'... No
Probing for `SPD EEPROM'... No
Next adapter: NVIDIA i2c adapter (i2c-4)
Do you want to scan it? (YES/no/selectively): y
Now follows a summary of the probes I have just done.
Just press ENTER to continue:
Driver `it87':
* ISA bus, address 0x290
Chip `ITE IT8712F Super IO Sensors' (confidence: 9)
Driver `k8temp' (autoloaded):
* Chip `AMD K8 thermal sensors' (confidence: 9)
To load everything that is needed, add this to /etc/modules:
#----cut here----
# Chip drivers
it87
#----cut here----
If you have some drivers built into your kernel, the list above will
contain too many modules. Skip the appropriate ones!
Do you want to add these lines automatically to /etc/modules? (yes/NO)y
Successful!
Monitoring programs won't work until the needed modules are
loaded. You may want to run '/etc/init.d/module-init-tools start'
to load them.
Unloading i2c-dev... OK
[/console]
чистка компьютера(полная у обычного пользователя снятие кулера его прочистка и т.д.) месяц назад
мать:Асус M2NX-Plus
процессор: AMD Athlon 64 X2 Dual Core Processor 5200+
Кулер чуть позже скажу потерял бумагу с названиями(
гуглил ничего толкового не нашел, пошарился по настройкам дебиана ничего не нашел.
в винде юзал спидфан. Причина того что ищю данную прогу, камп гудит очень сильно. oO
я видел и хочу понизить скорость. это понятно( просто программа не запускается.
это не программа понижения скорости, это датчики.
они всего-лишь констатируют состояние вашего железа. не более.
программа почти автоматическая. вот смотрите:
To load everything that is needed, add this to /etc/modules:
#----cut here----
# Chip drivers
it87
#----cut here----
в этой части программа сообщает, что загружено всё, что нужно
и можно еще добавить модуль it87
Do you want to add these lines automatically to /etc/modules? (yes/NO)y
Successful!
вы хотите добавить модуль автоматически? yes
успешно!
кулер этой программой Вы вряд ли отрегулируете...
Termo, я имел ввиду программу pwn-config, это я кинул свой лог на установки sensors-detect просто думаю там первопричина
surf, спасибо но это не то частоту потребления мне не нужно понижать мне нужно понизить обороты кулера. Пожалуйста читайте внимательно тему(
кулер не нашел свою модель т.к почему-то нет данных моделей производителя "Cool Kop" похож на мой только немного не то наверное (http://vzglyad-computers.kz/index.php?option=com_content&view=article&id=374:cool-cop-fan-s-478-1024-for-pentium&catid=55:coolers&Itemid=738)
а попробуйте найти в БИОСе функции CPU Smart FAN Control и CPU Smart FAN Mode и включить их - Enable
добавлено:
только что проверил на своей материнской плате (Gigabyte GA-M61P-S3)
достаточно включить CPU Smart FAN Control и обороты падают с 3026 до 1580
а попробуйте найти в БИОСе функции CPU Smart FAN Control и CPU Smart FAN Mode и включить их - Enable
Добавлю: зачастую там можно выбирать минимальную температуру включения(!) кулера да и среднюю температуру, которая будет поддерживаться - так что все же лучше пользоваться биосом, а не сторонними утилитами smile .
Ну и еще как вариант есть такие вещи в продаже - стабилизаторы напряжения, они обычно вставляются в пустое место (где напимер нет PCI планки) - ими можно вообще зафиксировать обороты (так-то напряжение на кулере) на нужном уровне, особенно полезно, когда у кулера нет четвертого провода на регулировку оборотов (у меня аналогичная вещь и я очень доволен).
Извините меня за мою тупость, но:
я зашел:
и там есть Q-Fan Function (только он) я его включил выставил по вашим рекомендациям температуру и ничего.
alex-seed, спасибо за совет со стабилизатором может придется его покупать.
Войдите или зарегистрируйтесь, чтобы ответить.
