3G МТС в Дебиане Squeeze

06.01.2011 07:48 #114081

Подскажите, как 3G МТС подключить в Дебиане Squeeze? Модем AnyDATA ADU-510A. В Убунте все работает, а в Дебиане не хочет. Пакеты usb-modeswitch и usb-modeswitch-data - есть.

Вот что пишет в Убунту:

iskatell@iskatell:~$ sudo ifconfig
[sudo] password for iskatell:

text

eth0      Link encap:Ethernet  HWaddr 88:ae:1d:2b:6d:1e 
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:17
lo        Link encap:Локальная петля (Loopback) 
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:168 errors:0 dropped:0 overruns:0 frame:0
          TX packets:168 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:13856 (13.8 KB)  TX bytes:13856 (13.8 KB)
ppp0      Link encap:Протокол PPP (Point-to-Point Protocol) 
          inet addr:77.52.251.242  P-t-P:80.255.77.48  Mask:255.255.255.255
          UP POINTOPOINT RUNNING NOARP MULTICAST  MTU:1500  Metric:1
          RX packets:25895 errors:0 dropped:0 overruns:0 frame:0
          TX packets:16151 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:3
          RX bytes:36225613 (36.2 MB)  TX bytes:943189 (943.1 KB)
wlan0     Link encap:Ethernet  HWaddr 78:e4:00:5c:93:17 
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

и вот что в Дебиане:

root@debian:/home/vit# ifconfig

text

eth0      Link encap:Ethernet  HWaddr 88:ae:1d:2b:6d:1e 
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:17
lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:24 errors:0 dropped:0 overruns:0 frame:0
          TX packets:24 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:1616 (1.5 KiB)  TX bytes:1616 (1.5 KiB)

root@debian:/home/vit# lsusb
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 003: ID 16d5:6502 AnyDATA Corporation CDMA/UMTS/GPRS modem
Bus 006 Device 002: ID 0458:0056 KYE Systems Corp. (Mouse Systems) Ergo 300 Mouse
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 004: ID 090c:37b1 Feiya Technology Corp.
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

06.01.2011 08:18 #114082

Iskatell, покажите

text


ls -l /dev/ttyUSB*

Также можете показать последние строк 20 команды dmesg, после подключения модема.

06.01.2011 11:39 #114117

Lupo Alberto написал:
Iskatell, покажите
text
ls -l /dev/ttyUSB*
Также можете показать последние строк 20 команды dmesg, после подключения модема.

vit@debian:~$ ls -l /dev/ttyUSB*
crw-rw---- 1 root dialout 188, 0 Янв 6 06:23 /dev/ttyUSB0
crw-rw---- 1 root dialout 188, 1 Янв 6 06:23 /dev/ttyUSB1
crw-rw---- 1 root dialout 188, 2 Янв 6 06:23 /dev/ttyUSB2
vit@debian:~$
dmesg....

Показать

1951736k
[ 9.372256] EXT3 FS on sda4, internal journal
[ 9.479640] loop: module loaded
[ 10.906025] fuse init (API version 7.13)
[ 12.196007] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input14
[ 12.776308] apm: BIOS not found.
[ 13.680994] Bluetooth: Core ver 2.15
[ 13.681048] NET: Registered protocol family 31
[ 13.681050] Bluetooth: HCI device and connection manager initialized
[ 13.681053] Bluetooth: HCI socket layer initialized
[ 13.904013] Bluetooth: L2CAP ver 2.14
[ 13.904016] Bluetooth: L2CAP socket layer initialized
[ 13.909496] Bluetooth: RFCOMM TTY layer initialized
[ 13.909501] Bluetooth: RFCOMM socket layer initialized
[ 13.909503] Bluetooth: RFCOMM ver 1.11vit@debian:~$ ls -l /dev/ttyUSB*
crw-rw---- 1 root dialout 188, 0 Янв 6 06:23 /dev/ttyUSB0
crw-rw---- 1 root dialout 188, 1 Янв 6 06:23 /dev/ttyUSB1
crw-rw---- 1 root dialout 188, 2 Янв 6 06:23 /dev/ttyUSB2
vit@debian:~$
dmesg....
1951736k
[ 9.372256] EXT3 FS on sda4, internal journal
[ 9.479640] loop: module loaded
[ 10.906025] fuse init (API version 7.13)
[ 12.196007] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input14
[ 12.776308] apm: BIOS not found.
[ 13.680994] Bluetooth: Core ver 2.15
[ 13.681048] NET: Registered protocol family 31
[ 13.681050] Bluetooth: HCI device and connection manager initialized
[ 13.681053] Bluetooth: HCI socket layer initialized
[ 13.904013] Bluetooth: L2CAP ver 2.14
[ 13.904016] Bluetooth: L2CAP socket layer initialized
[ 13.909496] Bluetooth: RFCOMM TTY layer initialized
[ 13.909501] Bluetooth: RFCOMM socket layer initialized
[ 13.909503] Bluetooth: RFCOMM ver 1.11
[ 14.076456] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 14.076459] Bluetooth: BNEP filters: protocol multicast
[ 14.131875] Bridge firewalling registered
[ 14.262187] Bluetooth: SCO (Voice Link) ver 0.6
[ 14.262190] Bluetooth: SCO socket layer initialized
[ 14.556261] b43 ssb0:0: firmware: requesting b43/ucode15.fw
[ 14.590319] b43 ssb0:0: firmware: requesting b43-open/ucode15.fw
[ 14.592729] b43-phy0 ERROR: Firmware file "b43/ucode15.fw" not found
[ 14.594612] b43-phy0 ERROR: Firmware file "b43-open/ucode15.fw" not found
[ 14.596609] b43-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware for this driver version. Please carefully read all instructions on this website.
[ 14.607227] tg3 0000:07:00.0: irq 31 for MSI/MSI-X
[ 14.639715] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 14.836264] b43 ssb0:0: firmware: requesting b43/ucode15.fw
[ 14.838714] b43 ssb0:0: firmware: requesting b43-open/ucode15.fw
[ 14.841116] b43-phy0 ERROR: Firmware file "b43/ucode15.fw" not found
[ 14.843282] b43-phy0 ERROR: Firmware file "b43-open/ucode15.fw" not found
[ 14.845388] b43-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware for this driver version. Please carefully read all instructions on this website.
[ 17.239123] lp: driver loaded but no devices found
[ 17.252184] ppdev: user-space parallel port driver
vit@debian:~$

[ 14.076456] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 14.076459] Bluetooth: BNEP filters: protocol multicast
[ 14.131875] Bridge firewalling registered
[ 14.262187] Bluetooth: SCO (Voice Link) ver 0.6
[ 14.262190] Bluetooth: SCO socket layer initialized
[ 14.556261] b43 ssb0:0: firmware: requesting b43/ucode15.fw
[ 14.590319] b43 ssb0:0: firmware: requesting b43-open/ucode15.fw
[ 14.592729] b43-phy0 ERROR: Firmware file "b43/ucode15.fw" not found
[ 14.594612] b43-phy0 ERROR: Firmware file "b43-open/ucode15.fw" not found
[ 14.596609] b43-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware for this driver version. Please carefully read all instructions on this website.
[ 14.607227] tg3 0000:07:00.0: irq 31 for MSI/MSI-X
[ 14.639715] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 14.836264] b43 ssb0:0: firmware: requesting b43/ucode15.fw
[ 14.838714] b43 ssb0:0: firmware: requesting b43-open/ucode15.fw
[ 14.841116] b43-phy0 ERROR: Firmware file "b43/ucode15.fw" not found
[ 14.843282] b43-phy0 ERROR: Firmware file "b43-open/ucode15.fw" not found
[ 14.845388] b43-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware for this driver version. Please carefully read all instructions on this website.
[ 17.239123] lp: driver loaded but no devices found
[ 17.252184] ppdev: user-space parallel port driver
vit@debian:~$

06.01.2011 11:44 #114120

Iskatell, модем определяется, какую программу дозвона используете?
Если в обоих дистрибутивах одну и ту же, можно попробовать просто перенести настройки. Да, и убедитесь, что пользователь, от которого пытаетесь дозвониться, входит в группу dialout.
P.S. В порядке «оффтопа», на будущее:

text


[   14.841116] b43-phy0 ERROR: Firmware file "b43/ucode15.fw" not found
[   14.843282] b43-phy0 ERROR: Firmware file "b43-open/ucode15.fw" not found
[   14.845388] b43-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Dri … cefirmware and download the correct firmware for this driver version. Please carefully read all instructions on this website.

Здесь подсказка, как настроить WiFi.

16.01.2011 20:44 · отредактировано #117736

доброго времени суток уважаемые.
нашел тему по поиску, переменная поиска была "Firmware file "b43/ucode15.fw" not found"
так что прошу не пинать к гуглу, мотивируя неумением пользоваться поиском.
в линуксе я новичок.
проблема в следующем, не работает wi-fi.
ноутбук hp-620
установлена squeeze.
вот лог загрузки

Показать

[ 0.583069] pci 0000:85:00.0: BAR 6: no parent found for of device [0xfffe0000-0xffffffff]
[ 0.583189] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:01
[ 0.583193] pci 0000:00:1c.0: IO window: 0x8000-0x8fff
[ 0.583199] pci 0000:00:1c.0: MEM window: 0xd8900000-0xd89fffff
[ 0.583204] pci 0000:00:1c.0: PREFETCH window: 0x000000d8b00000-0x000000d8cfffff
[ 0.583212] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:02
[ 0.583215] pci 0000:00:1c.1: IO window: 0x9000-0x9fff
[ 0.583221] pci 0000:00:1c.1: MEM window: 0xd8800000-0xd88fffff
[ 0.583226] pci 0000:00:1c.1: PREFETCH window: 0x000000d8d00000-0x000000d8efffff
[ 0.583233] pci 0000:00:1c.2: PCI bridge, secondary bus 0000:03
[ 0.583236] pci 0000:00:1c.2: IO window: 0x5000-0x6fff
[ 0.583242] pci 0000:00:1c.2: MEM window: 0xd4800000-0xd87fffff
[ 0.583247] pci 0000:00:1c.2: PREFETCH window: 0x000000d8f00000-0x000000d90fffff
[ 0.583254] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:44
[ 0.583257] pci 0000:00:1c.4: IO window: 0x3000-0x4fff
[ 0.583263] pci 0000:00:1c.4: MEM window: 0xd0800000-0xd47fffff
[ 0.583268] pci 0000:00:1c.4: PREFETCH window: 0x000000d9100000-0x000000d92fffff
[ 0.583277] pci 0000:00:1c.5: PCI bridge, secondary bus 0000:85
[ 0.583280] pci 0000:00:1c.5: IO window: 0x2000-0x2fff
[ 0.583286] pci 0000:00:1c.5: MEM window: 0xd0700000-0xd07fffff
[ 0.583291] pci 0000:00:1c.5: PREFETCH window: 0x000000d0400000-0x000000d04fffff
[ 0.583298] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:86
[ 0.583300] pci 0000:00:1e.0: IO window: disabled
[ 0.583306] pci 0000:00:1e.0: MEM window: 0xd0600000-0xd06fffff
[ 0.583310] pci 0000:00:1e.0: PREFETCH window: disabled
[ 0.583330] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.583335] pci 0000:00:1c.0: setting latency timer to 64
[ 0.583345] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.583350] pci 0000:00:1c.1: setting latency timer to 64
[ 0.583361] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.583365] pci 0000:00:1c.2: setting latency timer to 64
[ 0.583375] pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.583379] pci 0000:00:1c.4: setting latency timer to 64
[ 0.583389] pci 0000:00:1c.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.583393] pci 0000:00:1c.5: setting latency timer to 64
[ 0.583401] pci 0000:00:1e.0: setting latency timer to 64
[ 0.583405] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.583408] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[ 0.583410] pci_bus 0000:01: resource 0 io: [0x8000-0x8fff]
[ 0.583412] pci_bus 0000:01: resource 1 mem: [0xd8900000-0xd89fffff]
[ 0.583414] pci_bus 0000:01: resource 2 pref mem [0xd8b00000-0xd8cfffff]
[ 0.583417] pci_bus 0000:02: resource 0 io: [0x9000-0x9fff]
[ 0.583419] pci_bus 0000:02: resource 1 mem: [0xd8800000-0xd88fffff]
[ 0.583421] pci_bus 0000:02: resource 2 pref mem [0xd8d00000-0xd8efffff]
[ 0.583423] pci_bus 0000:03: resource 0 io: [0x5000-0x6fff]
[ 0.583425] pci_bus 0000:03: resource 1 mem: [0xd4800000-0xd87fffff]
[ 0.583427] pci_bus 0000:03: resource 2 pref mem [0xd8f00000-0xd90fffff]
[ 0.583430] pci_bus 0000:44: resource 0 io: [0x3000-0x4fff]
[ 0.583432] pci_bus 0000:44: resource 1 mem: [0xd0800000-0xd47fffff]
[ 0.583434] pci_bus 0000:44: resource 2 pref mem [0xd9100000-0xd92fffff]
[ 0.583436] pci_bus 0000:85: resource 0 io: [0x2000-0x2fff]
[ 0.583438] pci_bus 0000:85: resource 1 mem: [0xd0700000-0xd07fffff]
[ 0.583440] pci_bus 0000:85: resource 2 pref mem [0xd0400000-0xd04fffff]
[ 0.583442] pci_bus 0000:86: resource 1 mem: [0xd0600000-0xd06fffff]
[ 0.583444] pci_bus 0000:86: resource 3 io: [0x00-0xffff]
[ 0.583447] pci_bus 0000:86: resource 4 mem: [0x000000-0xffffffff]
[ 0.583473] NET: Registered protocol family 2
[ 0.583545] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.583789] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.584181] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.584427] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.584429] TCP reno registered
[ 0.584535] NET: Registered protocol family 1
[ 0.584553] pci 0000:00:02.0: Boot video device
[ 0.584839] Unpacking initramfs...
[ 0.792389] Freeing initrd memory: 8324k freed
[ 0.797091] audit: initializing netlink socket (disabled)
[ 0.797104] type=2000 audit(1295188838.795:1): initialized
[ 0.800144] highmem bounce pool size: 64 pages
[ 0.800148] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.801305] VFS: Disk quotas dquot_6.5.2
[ 0.801350] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.801410] msgmni has been set to 1708
[ 0.801569] alg: No test for stdrng (krng)
[ 0.801614] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.801617] io scheduler noop registered
[ 0.801618] io scheduler anticipatory registered
[ 0.801620] io scheduler deadline registered
[ 0.801649] io scheduler cfq registered (default)
[ 0.801783] pcieport 0000:00:1c.0: irq 24 for MSI/MSI-X
[ 0.801793] pcieport 0000:00:1c.0: setting latency timer to 64
[ 0.801945] pcieport 0000:00:1c.1: irq 25 for MSI/MSI-X
[ 0.801955] pcieport 0000:00:1c.1: setting latency timer to 64
[ 0.802101] pcieport 0000:00:1c.2: irq 26 for MSI/MSI-X
[ 0.802111] pcieport 0000:00:1c.2: setting latency timer to 64
[ 0.802256] pcieport 0000:00:1c.4: irq 27 for MSI/MSI-X
[ 0.802267] pcieport 0000:00:1c.4: setting latency timer to 64
[ 0.802413] pcieport 0000:00:1c.5: irq 28 for MSI/MSI-X
[ 0.802423] pcieport 0000:00:1c.5: setting latency timer to 64
[ 0.802583] isapnp: Scanning for PnP cards...
[ 1.157439] isapnp: No Plug & Play device found
[ 1.158641] Linux agpgart interface v0.103
[ 1.158703] agpgart-intel 0000:00:00.0: Intel Mobile Intel® GM45 Express Chipset
[ 1.159156] agpgart-intel 0000:00:00.0: detected 65532K stolen memory
[ 1.184964] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xc0000000
[ 1.185032] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.185388] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 1.187220] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 1.188042] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.188051] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 1.188053] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 1.188055] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 1.188058] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 1.188107] mice: PS/2 mouse device common for all mice
[ 1.188154] rtc_cmos 00:08: RTC can wake from S4
[ 1.188184] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0
[ 1.188214] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 1.188223] cpuidle: using governor ladder
[ 1.188224] cpuidle: using governor menu
[ 1.188227] No iBFT detected.
[ 1.188505] TCP cubic registered
[ 1.188620] NET: Registered protocol family 10
[ 1.188987] lo: Disabled Privacy Extensions
[ 1.189231] Mobile IPv6
[ 1.189233] NET: Registered protocol family 17
[ 1.189245] Using IPI No-Shortcut mode
[ 1.189300] PM: Resume from disk failed.
[ 1.189311] registered taskstats version 1
[ 1.190166] rtc_cmos 00:08: setting system clock to 2011-01-16 14:40:39 UTC (1295188839)
[ 1.190222] Initalizing network drop monitor service
[ 1.190242] Freeing unused kernel memory: 376k freed
[ 1.190405] Write protecting the kernel text: 2504k
[ 1.190423] Write protecting the kernel read-only data: 920k
[ 1.204737] udev[56]: starting version 164
[ 1.209653] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 1.341122] usbcore: registered new interface driver usbfs
[ 1.341261] usbcore: registered new interface driver hub
[ 1.341406] usbcore: registered new device driver usb
[ 1.353264] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.353301] ehci_hcd 0000:00:1a.7: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 1.353318] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 1.353321] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 1.353340] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 1.353371] ehci_hcd 0000:00:1a.7: debug port 1
[ 1.357268] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[ 1.361005] SCSI subsystem initialized
[ 1.361925] ehci_hcd 0000:00:1a.7: irq 19, io mem 0xd8a04c00
[ 1.363712] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 1.363751] r8169 0000:85:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 1.363851] r8169 0000:85:00.0: setting latency timer to 64
[ 1.364057] r8169 0000:85:00.0: irq 29 for MSI/MSI-X
[ 1.366004] eth0: RTL8102e at 0xf801e000, 1c:c1:de:a5:7e:3f, XID 04e00000 IRQ 29
[ 1.366330] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.378073] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 1.378096] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.378098] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.378100] usb usb1: Product: EHCI Host Controller
[ 1.378102] usb usb1: Manufacturer: Linux 2.6.32-5-686 ehci_hcd
[ 1.378104] usb usb1: SerialNumber: 0000:00:1a.7
[ 1.378233] usb usb1: configuration #1 chosen from 1 choice
[ 1.378293] hub 1-0:1.0: USB hub found
[ 1.378301] hub 1-0:1.0: 6 ports detected
[ 1.378372] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.378380] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 1.378384] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 1.378393] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 2
[ 1.378433] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000070c0
[ 1.378466] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.378468] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.378470] usb usb2: Product: UHCI Host Controller
[ 1.378472] usb usb2: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 1.378474] usb usb2: SerialNumber: 0000:00:1a.0
[ 1.378537] usb usb2: configuration #1 chosen from 1 choice
[ 1.378563] hub 2-0:1.0: USB hub found
[ 1.378569] hub 2-0:1.0: 2 ports detected
[ 1.378630] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 20 (level, low) -> IRQ 20
[ 1.378650] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 1.378653] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 1.378660] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 3
[ 1.378688] ehci_hcd 0000:00:1d.7: debug port 1
[ 1.382567] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 1.382584] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xd8a04800
[ 1.393606] libata version 3.00 loaded.
[ 1.402219] b43-pci-bridge 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 1.402234] b43-pci-bridge 0000:02:00.0: setting latency timer to 64
[ 1.404510] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 1.404542] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.404544] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.404546] usb usb3: Product: EHCI Host Controller
[ 1.404548] usb usb3: Manufacturer: Linux 2.6.32-5-686 ehci_hcd
[ 1.404550] usb usb3: SerialNumber: 0000:00:1d.7
[ 1.404620] usb usb3: configuration #1 chosen from 1 choice
[ 1.404645] hub 3-0:1.0: USB hub found
[ 1.404652] hub 3-0:1.0: 6 ports detected
[ 1.404741] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 1.404749] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 1.404753] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 1.404764] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[ 1.404802] uhci_hcd 0000:00:1a.1: irq 17, io base 0x000070a0
[ 1.404835] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.404838] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.404840] usb usb4: Product: UHCI Host Controller
[ 1.404841] usb usb4: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 1.404843] usb usb4: SerialNumber: 0000:00:1a.1
[ 1.404899] usb usb4: configuration #1 chosen from 1 choice
[ 1.404924] hub 4-0:1.0: USB hub found
[ 1.404931] hub 4-0:1.0: 2 ports detected
[ 1.405138] ahci 0000:00:1f.2: version 3.0
[ 1.405155] ahci 0000:00:1f.2: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 1.405204] ahci 0000:00:1f.2: irq 30 for MSI/MSI-X
[ 1.405257] ahci: SSS flag set, parallel bus scan disabled
[ 1.405292] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 4 ports 3 Gbps 0x23 impl SATA mode
[ 1.405296] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ccc ems
[ 1.405301] ahci 0000:00:1f.2: setting latency timer to 64
[ 1.420254] scsi0 : ahci
[ 1.420742] scsi1 : ahci
[ 1.420839] scsi2 : ahci
[ 1.420933] scsi3 : ahci
[ 1.421027] scsi4 : ahci
[ 1.421121] scsi5 : ahci
[ 1.460287] ssb: Sonics Silicon Backplane found on PCI device 0000:02:00.0
[ 1.636856] ata1: SATA max UDMA/133 abar m2048@0xd8a04000 port 0xd8a04100 irq 30
[ 1.636860] ata2: SATA max UDMA/133 abar m2048@0xd8a04000 port 0xd8a04180 irq 30
[ 1.636862] ata3: DUMMY
[ 1.636863] ata4: DUMMY
[ 1.636865] ata5: DUMMY
[ 1.636867] ata6: SATA max UDMA/133 abar m2048@0xd8a04000 port 0xd8a04380 irq 30
[ 1.636920] uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.636929] uhci_hcd 0000:00:1a.2: setting latency timer to 64
[ 1.636932] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[ 1.636943] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
[ 1.636981] uhci_hcd 0000:00:1a.2: irq 18, io base 0x00007080
[ 1.637017] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.637020] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.637022] usb usb5: Product: UHCI Host Controller
[ 1.637023] usb usb5: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 1.637025] usb usb5: SerialNumber: 0000:00:1a.2
[ 1.637093] usb usb5: configuration #1 chosen from 1 choice
[ 1.637119] hub 5-0:1.0: USB hub found
[ 1.637126] hub 5-0:1.0: 2 ports detected
[ 1.637180] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 1.637187] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 1.637191] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.637198] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
[ 1.637225] uhci_hcd 0000:00:1d.0: irq 20, io base 0x00007060
[ 1.637255] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.637257] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.637259] usb usb6: Product: UHCI Host Controller
[ 1.637261] usb usb6: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 1.637263] usb usb6: SerialNumber: 0000:00:1d.0
[ 1.637318] usb usb6: configuration #1 chosen from 1 choice
[ 1.637342] hub 6-0:1.0: USB hub found
[ 1.637348] hub 6-0:1.0: 2 ports detected
[ 1.637400] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 22 (level, low) -> IRQ 22
[ 1.637407] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 1.637410] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.637417] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
[ 1.637452] uhci_hcd 0000:00:1d.1: irq 22, io base 0x00007040
[ 1.637483] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.637485] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.637488] usb usb7: Product: UHCI Host Controller
[ 1.637489] usb usb7: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 1.637491] usb usb7: SerialNumber: 0000:00:1d.1
[ 1.637549] usb usb7: configuration #1 chosen from 1 choice
[ 1.637573] hub 7-0:1.0: USB hub found
[ 1.637579] hub 7-0:1.0: 2 ports detected
[ 1.637629] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.637636] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 1.637639] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 1.637649] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
[ 1.637675] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00007020
[ 1.637707] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.637709] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.637711] usb usb8: Product: UHCI Host Controller
[ 1.637713] usb usb8: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 1.637715] usb usb8: SerialNumber: 0000:00:1d.2
[ 1.637770] usb usb8: configuration #1 chosen from 1 choice
[ 1.637793] hub 8-0:1.0: USB hub found
[ 1.637798] hub 8-0:1.0: 2 ports detected
[ 1.800011] usb 1-5: new high speed USB device using ehci_hcd and address 3
[ 1.898678] thermal LNXTHERM:01: registered as thermal_zone0
[ 1.898687] ACPI: Thermal Zone [GFXZ] (16 C)
[ 1.908742] thermal LNXTHERM:02: registered as thermal_zone1
[ 1.908750] ACPI: Thermal Zone [DTSZ] (45 C)
[ 1.914391] thermal LNXTHERM:03: registered as thermal_zone2
[ 1.914400] ACPI: Thermal Zone [CPUZ] (48 C)
[ 1.918289] thermal LNXTHERM:04: registered as thermal_zone3
[ 1.918295] ACPI: Thermal Zone [SKNZ] (38 C)
[ 1.928980] thermal LNXTHERM:05: registered as thermal_zone4
[ 1.928987] ACPI: Thermal Zone [BATZ] (27 C)
[ 1.932706] thermal LNXTHERM:06: registered as thermal_zone5
[ 1.932713] ACPI: Thermal Zone [FDTZ] (30 C)
[ 1.956022] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.957667] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 1.957755] ata1.00: ATA-8: WDC WD3200BEKT-60KA9T0, 01.01A01, max UDMA/133
[ 1.957758] ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.959472] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 1.959572] ata1.00: configured for UDMA/133
[ 1.964592] usb 1-5: New USB device found, idVendor=0461, idProduct=4db6
[ 1.964594] usb 1-5: New USB device strings: Mfr=2, Product=1, SerialNumber=3
[ 1.964596] usb 1-5: Product: Villem
[ 1.964598] usb 1-5: Manufacturer: Primax Electronics Ltd.
[ 1.964600] usb 1-5: SerialNumber: PMX01
[ 1.964675] usb 1-5: configuration #1 chosen from 1 choice
[ 1.972116] scsi 0:0:0:0: Direct-Access ATA WDC WD3200BEKT-6 01.0 PQ: 0 ANSI: 5
[ 2.208006] usb 2-1: new full speed USB device using uhci_hcd and address 2
[ 2.378465] usb 2-1: New USB device found, idVendor=03f0, idProduct=231d
[ 2.378467] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.378470] usb 2-1: Product: HP Integrated Module
[ 2.378471] usb 2-1: Manufacturer: Broadcom Corp
[ 2.378535] usb 2-1: configuration #1 chosen from 1 choice
[ 2.696023] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.714651] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 2.714655] ata2.00: ATAPI: hp CDDVDW TS-L633N, 0300, max UDMA/100
[ 2.737864] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 2.737887] ata2.00: configured for UDMA/100
[ 2.752541] scsi 1:0:0:0: CD-ROM hp CDDVDW TS-L633N 0300 PQ: 0 ANSI: 5
[ 2.872006] usb 8-2: new full speed USB device using uhci_hcd and address 2
[ 3.043706] usb 8-2: New USB device found, idVendor=09da, idProduct=054f
[ 3.043709] usb 8-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.043711] usb 8-2: Product: USB Device
[ 3.043712] usb 8-2: Manufacturer: A4TECH
[ 3.043779] usb 8-2: configuration #1 chosen from 1 choice
[ 3.072017] ata6: SATA link down (SStatus 0 SControl 300)
[ 3.093239] fan PNP0C0B:00: registered as cooling_device0
[ 3.093245] ACPI: Fan [FAN6] (off)
[ 3.093462] fan PNP0C0B:01: registered as cooling_device1
[ 3.093467] ACPI: Fan [FAN7] (off)
[ 3.093678] fan PNP0C0B:02: registered as cooling_device2
[ 3.093688] ACPI: Fan [FAN8] (off)
[ 3.093901] fan PNP0C0B:03: registered as cooling_device3
[ 3.093905] ACPI: Fan [FAN9] (off)
[ 3.094115] fan PNP0C0B:04: registered as cooling_device4
[ 3.094120] ACPI: Fan [FANA] (off)
[ 3.094329] fan PNP0C0B:05: registered as cooling_device5
[ 3.094333] ACPI: Fan [FANB] (off)
[ 3.094444] fan PNP0C0B:06: registered as cooling_device6
[ 3.094448] ACPI: Fan [FANG] (off)
[ 3.094661] fan PNP0C0B:07: registered as cooling_device7
[ 3.094666] ACPI: Fan [FAN0] (off)
[ 3.094873] fan PNP0C0B:08: registered as cooling_device8
[ 3.094877] ACPI: Fan [FAN1] (off)
[ 3.095085] fan PNP0C0B:09: registered as cooling_device9
[ 3.095089] ACPI: Fan [FAN2] (off)
[ 3.095297] fan PNP0C0B:0a: registered as cooling_device10
[ 3.095302] ACPI: Fan [FAN3] (off)
[ 3.095513] fan PNP0C0B:0b: registered as cooling_device11
[ 3.095518] ACPI: Fan [FAN4] (off)
[ 3.095733] fan PNP0C0B:0c: registered as cooling_device12
[ 3.095738] ACPI: Fan [FAN5] (off)
[ 3.111625] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[ 3.111668] sd 0:0:0:0: [sda] Write Protect is off
[ 3.111671] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.111689] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.111801] sda:
[ 3.121053] usbcore: registered new interface driver hiddev
[ 3.125108] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1d.2/usb8/8-2/8-2:1.0/input/input1
[ 3.125189] generic-usb 0003:09DA:054F.0001: input,hiddev0,hidraw0: USB HID v1.11 Keyboard [A4TECH USB Device] on usb-0000:00:1d.2-2/input0
[ 3.126935] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1d.2/usb8/8-2/8-2:1.1/input/input2
[ 3.126987] generic-usb 0003:09DA:054F.0002: input,hidraw1: USB HID v1.11 Mouse [A4TECH USB Device] on usb-0000:00:1d.2-2/input1
[ 3.127009] usbcore: registered new interface driver usbhid
[ 3.127011] usbhid: v2.6:USB HID core driver
[ 3.165861] sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 >
[ 3.198713] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.206923] sr0: scsi3-mmc drive: 62x/62x writer dvd-ram cd/rw xa/form2 cdda tray
[ 3.206927] Uniform CD-ROM driver Revision: 3.20
[ 3.207022] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 3.211083] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.211116] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 3.752865] kjournald starting. Commit interval 5 seconds
[ 3.752872] EXT3-fs: mounted filesystem with ordered data mode.
[ 4.468480] udev[502]: starting version 164
[ 4.570709] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input3
[ 4.570716] ACPI: Sleep Button [SLPB]
[ 4.570763] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input4
[ 4.570879] ACPI: Lid Switch [LID]
[ 4.570931] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input5
[ 4.570934] ACPI: Power Button [PWRF]
[ 4.582086] ACPI: SSDT bbac6c98 00233 (v01 PmRef Cpu0Ist 00003000 INTL 20060912)
[ 4.582653] ACPI: SSDT bbac4618 0057B (v01 PmRef Cpu0Cst 00003001 INTL 20060912)
[ 4.632625] Monitor-Mwait will be used to enter C-1 state
[ 4.651432] ACPI: Battery Slot [BAT0] (battery present)
[ 4.666902] Monitor-Mwait will be used to enter C-2 state
[ 4.666914] Marking TSC unstable due to TSC halts in idle
[ 4.667023] processor LNXCPU:00: registered as cooling_device13
[ 4.667543] ACPI: SSDT bbac5e18 001D7 (v01 PmRef ApIst 00003000 INTL 20060912)
[ 4.667960] ACPI: SSDT bbac6f18 0008D (v01 PmRef ApCst 00003000 INTL 20060912)
[ 4.685263] Switching to clocksource hpet
[ 4.690246] processor LNXCPU:01: registered as cooling_device14
[ 4.748321] ACPI: AC Adapter [AC] (off-line)
[ 4.749129] ACPI: WMI: Mapper loaded
[ 4.753111] input: PC Speaker as /devices/platform/pcspkr/input/input6
[ 4.804256] cfg80211: Using static regulatory domain info
[ 4.804258] cfg80211: Regulatory domain: US
[ 4.804260] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 4.804262] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
[ 4.804265] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 4.804267] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 4.804269] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 4.804272] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 4.804274] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
[ 4.804832] cfg80211: Calling CRDA for country: US
[ 4.812225] Bluetooth: Core ver 2.15
[ 4.813297] NET: Registered protocol family 31
[ 4.813299] Bluetooth: HCI device and connection manager initialized
[ 4.813301] Bluetooth: HCI socket layer initialized
[ 4.926583] [drm] Initialized drm 1.1.0 20060810
[ 5.100962] Bluetooth: Generic Bluetooth USB driver ver 0.6
[ 5.101171] usbcore: registered new interface driver btusb
[ 5.116983] Linux video capture interface: v2.00
[ 5.131333] uvcvideo: Found UVC 1.00 device Villem (0461:4db6)
[ 5.138939] input: Villem as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5:1.0/input/input7
[ 5.138988] usbcore: registered new interface driver uvcvideo
[ 5.138991] USB Video Class driver (v0.1.0)
[ 5.185379] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 5.185384] i915 0000:00:02.0: setting latency timer to 64
[ 5.193865] i915 0000:00:02.0: irq 31 for MSI/MSI-X
[ 5.193872] [drm] set up 63M of stolen space
[ 5.226550] b43-phy0: Broadcom 4312 WLAN found (core revision 15)
[ 5.342267] phy0: Selected rate control algorithm 'minstrel'
[ 5.342817] Registered led device: b43-phy0::tx
[ 5.342831] Registered led device: b43-phy0::rx
[ 5.342844] Registered led device: b43-phy0::radio
[ 5.342899] Broadcom 43xx driver loaded [ Features: PMLS, Firmware-ID: FW13 ]
[ 5.538794] Synaptics Touchpad, model: 1, fw: 7.4, id: 0x1e0b1, caps: 0xd04771/0xa40000/0xa0400
[ 5.580419] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input8
[ 5.960844] Console: switching to colour frame buffer device 170x48
[ 5.965099] fb0: inteldrmfb frame buffer device
[ 5.965100] registered panic notifier
[ 5.970032] acpi device:08: registered as cooling_device15
[ 5.970696] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:01/input/input9
[ 5.970742] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 5.970780] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 5.975997] HDA Intel 0000:00:1b.0: power state changed by ACPI to D0
[ 5.976061] HDA Intel 0000:00:1b.0: power state changed by ACPI to D0
[ 5.976069] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 5.976122] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 6.672322] EXT3 FS on sda3, internal journal
[ 6.734783] loop: module loaded
[ 7.832249] kjournald starting. Commit interval 5 seconds
[ 7.832542] EXT3 FS on sda8, internal journal
[ 7.832545] EXT3-fs: mounted filesystem with ordered data mode.
[ 7.837217] kjournald starting. Commit interval 5 seconds
[ 7.837432] EXT3 FS on sda7, internal journal
[ 7.837435] EXT3-fs: mounted filesystem with ordered data mode.
[ 7.853260] kjournald starting. Commit interval 5 seconds
[ 7.853532] EXT3 FS on sda5, internal journal
[ 7.853535] EXT3-fs: mounted filesystem with ordered data mode.
[ 7.858202] kjournald starting. Commit interval 5 seconds
[ 7.858438] EXT3 FS on sda6, internal journal
[ 7.858441] EXT3-fs: mounted filesystem with ordered data mode.
[ 8.837541] fuse init (API version 7.13)
[ 9.928006] apm: BIOS not found.
[ 10.618952] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input10
[ 11.020744] b43 ssb0:0: firmware: requesting b43/ucode15.fw
[ 11.136841] b43 ssb0:0: firmware: requesting b43-open/ucode15.fw
[ 11.138923] b43-phy0 ERROR: Firmware file "b43/ucode15.fw" not found
[ 11.140329] b43-phy0 ERROR: Firmware file "b43-open/ucode15.fw" not found
[ 11.141854] b43-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware for this driver version. Please carefully read all instructions on this website.
[ 11.146839] r8169: eth0: link down
[ 11.147025] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 11.540262] b43 ssb0:0: firmware: requesting b43/ucode15.fw
[ 11.542450] b43 ssb0:0: firmware: requesting b43-open/ucode15.fw
[ 11.545732] b43-phy0 ERROR: Firmware file "b43/ucode15.fw" not found
[ 11.547366] b43-phy0 ERROR: Firmware file "b43-open/ucode15.fw" not found
[ 11.549081] b43-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware for this driver version. Please carefully read all instructions on this website.
[ 12.286435] Bluetooth: L2CAP ver 2.14
[ 12.286438] Bluetooth: L2CAP socket layer initialized
[ 12.319256] Bluetooth: RFCOMM TTY layer initialized
[ 12.319260] Bluetooth: RFCOMM socket layer initialized
[ 12.319261] Bluetooth: RFCOMM ver 1.11
[ 12.465936] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 12.465938] Bluetooth: BNEP filters: protocol multicast
[ 12.504201] Bridge firewalling registered
[ 12.529456] Bluetooth: SCO (Voice Link) ver 0.6
[ 12.529458] Bluetooth: SCO socket layer initialized
[ 12.703632] lp: driver loaded but no devices found
[ 12.733002] ppdev: user-space parallel port driver
[ 20.991353] CPU0 attaching NULL sched-domain.
[ 20.991358] CPU1 attaching NULL sched-domain.
[ 21.020127] CPU0 attaching sched-domain:
[ 21.020131] domain 0: span 0-1 level MC
[ 21.020133] groups: 0 1
[ 21.020137] domain 1: span 0-1 level CPU
[ 21.020139] groups: 0-1 (cpu_power = 2048)
[ 21.020145] CPU1 attaching sched-domain:
[ 21.020147] domain 0: span 0-1 level MC
[ 21.020148] groups: 1 0
[ 21.020151] domain 1: span 0-1 level CPU
[ 21.020153] groups: 0-1 (cpu_power = 2048)
[ 39.118724] UDF-fs: No VRS found
[ 39.118729] UDF-fs: No partition found (1)
[ 40.118977] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 40.201418] ISO 9660 Extensions: RRIP_1991A
[ 46.552115] usb 3-5: new high speed USB device using ehci_hcd and address 3
[ 46.694154] usb 3-5: New USB device found, idVendor=0951, idProduct=1613
[ 46.694160] usb 3-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 46.694164] usb 3-5: Product: DT 101 II
[ 46.694167] usb 3-5: Manufacturer: Kingston
[ 46.694170] usb 3-5: SerialNumber: 5B8907000158
[ 46.694312] usb 3-5: configuration #1 chosen from 1 choice
[ 46.760351] Initializing USB Mass Storage driver...
[ 46.760507] scsi6 : SCSI emulation for USB Mass Storage devices
[ 46.760593] usbcore: registered new interface driver usb-storage
[ 46.760596] USB Mass Storage support registered.
[ 46.761260] usb-storage: device found at 3
[ 46.761262] usb-storage: waiting for device to settle before scanning
[ 51.760372] usb-storage: device scan complete
[ 51.761443] scsi 6:0:0:0: Direct-Access Kingston DT 101 II PMAP PQ: 0 ANSI: 0 CCS
[ 51.762516] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 52.209311] sd 6:0:0:0: [sdb] 7903232 512-byte logical blocks: (4.04 GB/3.76 GiB)
[ 52.209793] sd 6:0:0:0: [sdb] Write Protect is off
[ 52.209798] sd 6:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 52.209802] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 52.211917] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 52.211924] sdb: sdb1
[ 52.214154] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 52.214161] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 52.763049] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
sonik@debian:~$

собственно смущает первая строка, именно она вылезает после выбора ОС в грубе, и после нее уже идет загрузка системы
то есть выглядит это примерно так

pci 0000:85:00.0: BAR 6: no parent found for of device
loading, please wait...

ну и следом идет уже то, что я выложил выше.

далее, строки с ошибками(выделены), где указывается url, который нужно посетить для решения данной проблемы.
посещаю этот самый url
делаю все по инструкции

root@debian:~# lspci -vnn | grep 14e4
02:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] (rev 01)

то есть PCI-ID 14e4:4315
чип карты BCM4312
дкайвер b43/wl
согласно приведенной таблице на том url
partially supported 2.6.33 and later (PIO mode) поддерживается ядром 2.6.33 и выше.
далее инфа на сайте

Supported chip types
* BCM4303 (802.11b-only chips, uses b43legacy)
* BCM4306 (Rev. 2 uses b43legacy, Rev. 3 uses b43)
* BCM4309 (only the 2.4GHz part)
* BCM4311 rev 1 / BCM4312
* BCM4311 rev 2 / BCM4312 (needs patches for 2.6.24)
* BCM4312 with a/b/g (only the 2.4GHz part)
* BCM4313 with b/g (partially supported in 2.6.32, however 2.6.33 or latter is recommended)
* BCM4315 (BCM4312 LP/PHY. linux-kernel 2.6.32 is needed, 2.6.33 or latter is recommended)
* BCM4318

но на моей скузе ядро 2.6.32( чип выделен)
читаем дальше

There are different versions of firmware and tools you may need:

тут таблица. выбираю

b43 Linux-2.6.31 and newer, compat-wireless-2.6 package, current GIT trees - for LP-PHY cards 4.178.10.4 b43-fwcutter v. 13

жму Go и попадаю на другую страницу

You are using the b43 driver with an LP-PHY card (e.g. BCM4312)

Follow these instructions if you are using the b43 driver from linux-2.6.32 and newer or compat-wireless-2.6, or from any current GIT tree, and have a device with a low-power PHY.

Install b43-fwcutter, then use version 4.174.64.19 of Broadcom's proprietary driver. (The tarball is mislabeled as "4.178.10.4", but it is actually 4.174.64.19.)
Download and extract the firmware from this driver tarball:

далее делаю все по пунктам как показано

1 export FIRMWARE_INSTALL_DIR="/lib/firmware"
2 wget http://downloads.openwrt.org/sources/broadcom-wl-4.178.10.4.tar.bz2
3 tar xjf broadcom-wl-4.178.10.4.tar.bz2
4 cd broadcom-wl-4.178.10.4/linux
5 sudo ../../b43-fwcutter-013/b43-fwcutter -w "$FIRMWARE_INSTALL_DIR" wl_apsta.o

и тут наступают трудности.
как я понял, первое действие указывает путь куда следует устанавливать фирмварное по, путь совпадает.
второе - закачка по
третье - разорхивирование пакета
четвертое -переход в директорию
и в пятом - нужно чего то выполнить, непонятно что и зачем и почему. у меня не получается, вот мои действия.

root@debian:~# export FIRMWARE_INSTALL_DIR="/lib/firmware"
root@debian:~# wget http://downloads.openwrt.org/sources/broadcom-wl-4.178.10.4.tar.bz2
--2011-01-16 20:32:18-- http://downloads.openwrt.org/sources/broadcom-wl-4.178.10.4.tar.bz2
Распознаётся downloads.openwrt.org... 78.24.191.177
Устанавливается соединение с downloads.openwrt.org|78.24.191.177|:80... соединение установлено.
Запрос HTTP послан, ожидается ответ... 200 OK
Длина: 5986780 (5,7M) [text/plain]
Saving to: «broadcom-wl-4.178.10.4.tar.bz2»

100%[======================================>] 5 986 780 256K/s в 25s

2011-01-16 20:32:45 (236 KB/s) - «broadcom-wl-4.178.10.4.tar.bz2» saved [5986780/5986780]

root@debian:~# tar xjf broadcom-wl-4.178.10.4.tar.bz2
root@debian:~# cd broadcom-wl-4.178.10.4/linux
root@debian:~/broadcom-wl-4.178.10.4/linux# ../..b43-fwcutter-013/b43-fwcutter -w "$FIRMWARE_INSTALL_DIR" wl_apsta.o
bash: ../..b43-fwcutter-013/b43-fwcutter: Нет такого файла или каталога
root@debian:~/broadcom-wl-4.178.10.4/linux#

совсем непонятно, что есть пятое действие?
хочу знать как все это происходит в деталях.
хотя бы укажите направление куда следует копать. спасибо.

16.01.2011 20:55 #117741

сантехник написал:
bash: ../..b43-fwcutter-013/b43-fwcutter: Нет такого файла или каталога

сантехник написал:
5 sudo ../../b43-fwcutter-013/b43-fwcutter -w "$FIRMWARE_INSTALL_DIR" wl_apsta.o

слеш забыли :(

16.01.2011 21:33 · отредактировано #117756

drBatty написал:
[quote=сантехник]bash: ../..b43-fwcutter-013/b43-fwcutter: Нет такого файла или каталога

сантехник написал:
5 sudo ../../b43-fwcutter-013/b43-fwcutter -w "$FIRMWARE_INSTALL_DIR" wl_apsta.o

слеш забыли :([/quote]
спасибо. но сути не меняет

root@debian:~/broadcom-wl-4.178.10.4/linux# ../../b43-fwcutter-013/b43-fwcutter -w "$FIRMWARE_INSTALL_DIR" wl_apsta.o
bash: ../../b43-fwcutter-013/b43-fwcutter: Нет такого файла или каталога
root@debian:~/broadcom-wl-4.178.10.4/linux#

и вообще что это за операция такая? ../../ ???

16.01.2011 21:39 #117757

сантехник, повторите ещё раз всё сначала, только вместо tar xjf напишите tar xjvvf
и покажите, что вывела эта команда...

сантехник написал:
совсем непонятно, что есть пятое действие?

как раз запуск скрипта установки. ../ это каталог на 1 уровень выше, соответственно, у вас ../../ это видимо домашний каталог. наверное /root/
оттуда и ищется распакованный вами /root/b43-fwcutter-013/b43-fwcutter. только почему-то не находится.

16.01.2011 21:46 #117758

кстати, для дебиана там такое написано:

Ubuntu/Debian

In recent versions of Ubuntu and Debian, installing the b43-fwcutter package will handle everything for you:

Переключить отображение номеров строк

1 sudo apt-get install b43-fwcutter

You will be asked to automatically fetch and install the firmware into the right location.

Update: Ubuntu has a page detailing on how one goes about installing broadcom wireless drivers on their community documentation.

If you have internet access on the device that has a b43 supported broadcom wireless chipset and would like to use b43, follow this link: https://help.ubuntu.com/community/WifiDocs/Driver/bcm43xx#b43%20-%20Internet%20access .

If you do not have internet access on the device that has a b43 supported broadcom wireless chipset and would like to use b43, follow this link instead: https://help.ubuntu.com/community/WifiDocs/Driver/bcm43xx#b43%20-%20No%20Internet%20access .

Note that you can only follow one of the two guides, not both.

16.01.2011 21:49 #117760

а если вы не хотите так, то вам надо установщик поставить сначала:

Install b43-fwcutter

Use version 013 of b43-fwcutter.
Download, extract the b43-fwcutter tarball and build it:

Переключить отображение номеров строк

1 wget http://bu3sch.de/b43/fwcutter/b43-fwcutter-013.tar.bz2
2 tar xjf b43-fwcutter-013.tar.bz2
3 cd b43-fwcutter-013
4 make
5 cd ..

16.01.2011 22:54 #117798

drBatty написал:
сантехник, повторите ещё раз всё сначала, только вместо tar xjf напишите tar xjvvf
и покажите, что вывела эта команда...

root@debian:/home/sonik# export FIRMWARE_INSTALL_DIR="/lib/firmware"
root@debian:/home/sonik# wget http://downloads.openwrt.org/sources/broadcom-wl-4.178.10.4.tar.bz2
--2011-01-16 22:43:45-- http://downloads.openwrt.org/sources/broadcom-wl-4.178.10.4.tar.bz2
Распознаётся downloads.openwrt.org... 78.24.191.177
Устанавливается соединение с downloads.openwrt.org|78.24.191.177|:80... соединение установлено.
Запрос HTTP послан, ожидается ответ... 200 OK
Длина: 5986780 (5,7M) [text/plain]
Saving to: «broadcom-wl-4.178.10.4.tar.bz2.3»

100%[======================================>] 5 986 780 226K/s в 28s

2011-01-16 22:44:13 (212 KB/s) - «broadcom-wl-4.178.10.4.tar.bz2.3» saved [5986780/5986780]

root@debian:/home/sonik# tar xjvvf broadcom-wl-4.178.10.4.tar.bz2drwxr-xr-x hauke/hauke 0 2009-02-19 21:45 broadcom-wl-4.178.10.4/
drwxr-xr-x hauke/hauke 0 2009-02-19 21:41 broadcom-wl-4.178.10.4/config/
-rw-r--r-- hauke/hauke 512 2009-02-19 21:41 broadcom-wl-4.178.10.4/config/wlconfig_nomimo
-rw-r--r-- hauke/hauke 774 2009-02-19 21:41 broadcom-wl-4.178.10.4/config/wlconfig_lx_router_apsta_1chipG
-rw-r--r-- hauke/hauke 536 2009-02-19 21:41 broadcom-wl-4.178.10.4/config/wlconfig_lx_wl_sdstd
-rw-r--r-- hauke/hauke 586 2009-02-19 21:41 broadcom-wl-4.178.10.4/config/wlconfig_lx_shared
-rwxr-xr-x hauke/hauke 188 2009-02-19 21:41 broadcom-wl-4.178.10.4/config/diffupdate.sh
-rw-r--r-- hauke/hauke 769 2009-02-19 21:41 broadcom-wl-4.178.10.4/config/wlconfig_lx_router_ap_1chipG
-rw-r--r-- hauke/hauke 673 2009-02-19 21:41 broadcom-wl-4.178.10.4/config/wlconfig_lx_router_ap
-rw-r--r-- hauke/hauke 761 2009-02-19 21:41 broadcom-wl-4.178.10.4/config/wlconfig_lx_router_ap_sdstd
-rw-r--r-- hauke/hauke 8822 2009-02-19 21:41 broadcom-wl-4.178.10.4/config/wl.mk
-rw-r--r-- hauke/hauke 734 2009-02-19 21:41 broadcom-wl-4.178.10.4/config/wltunable_lx_router.h
-rw-r--r-- hauke/hauke 702 2009-02-19 21:41 broadcom-wl-4.178.10.4/config/wlconfig_lx_router_sta
-rw-r--r-- hauke/hauke 766 2009-02-19 21:41 broadcom-wl-4.178.10.4/config/wl_default
-rw-r--r-- hauke/hauke 993 2009-02-19 21:41 broadcom-wl-4.178.10.4/config/wltunable_lx_router_1chipG.h
-rw-r--r-- hauke/hauke 568 2009-02-19 21:41 broadcom-wl-4.178.10.4/config/wl_hnd
-rw-r--r-- hauke/hauke 770 2009-02-19 21:41 broadcom-wl-4.178.10.4/config/wlconfig_lx_router_sta_1chipG
-rw-r--r-- hauke/hauke 739 2009-02-19 21:41 broadcom-wl-4.178.10.4/config/wlconfig_lx_router_apsta
-rw-r--r-- hauke/hauke 621 2009-02-19 21:41 broadcom-wl-4.178.10.4/config/wlconfig_apdef
-rw-r--r-- hauke/hauke 246 2009-02-19 21:45 broadcom-wl-4.178.10.4/README
drwxr-xr-x hauke/hauke 0 2009-02-19 21:41 broadcom-wl-4.178.10.4/linux/
-rw-r--r-- hauke/hauke 8875011 2009-02-19 21:41 broadcom-wl-4.178.10.4/linux/wl_sta.o
-rw-r--r-- hauke/hauke 1432012 2009-02-19 21:41 broadcom-wl-4.178.10.4/linux/wl.o
-rw-r--r-- hauke/hauke 8185623 2009-02-19 21:41 broadcom-wl-4.178.10.4/linux/wl_ap.o
-rw-r--r-- hauke/hauke 9900134 2009-02-19 21:41 broadcom-wl-4.178.10.4/linux/wl_apsta.o
root@debian:/home/sonik# cd broadcom-wl-4.178.10.4/linux
root@debian:/home/sonik/broadcom-wl-4.178.10.4/linux# ../../b43-fwcutter-013/b43-fwcutter -w "$FIRMWARE_INSTALL_DIR" wl_apsta.o
bash: ../../b43-fwcutter-013/b43-fwcutter: Нет такого файла или каталога
root@debian:/home/sonik/broadcom-wl-4.178.10.4/linux#

drBatty написал:

как раз запуск скрипта установки. ../ это каталог на 1 уровень выше, соответственно, у вас ../../ это видимо домашний каталог. наверное /root/
оттуда и ищется распакованный вами /root/b43-fwcutter-013/b43-fwcutter. только почему-то не находится.

да. нет такого каталога. вручную поглядел

16.01.2011 22:55 #117801

drBatty написал:
кстати, для дебиана там такое написано:

Ubuntu/Debian

In recent versions of Ubuntu and Debian, installing the b43-fwcutter package will handle everything for you:

Переключить отображение номеров строк

1 sudo apt-get install b43-fwcutter

You will be asked to automatically fetch and install the firmware into the right location.

Update: Ubuntu has a page detailing on how one goes about installing broadcom wireless drivers on their community documentation.

If you have internet access on the device that has a b43 supported broadcom wireless chipset and would like to use b43, follow this link: https://help.ubuntu.com/community/WifiDocs/Driver/bcm43xx#b43%20-%20Internet%20access .

If you do not have internet access on the device that has a b43 supported broadcom wireless chipset and would like to use b43, follow this link instead: https://help.ubuntu.com/community/WifiDocs/Driver/bcm43xx#b43%20-%20No%20Internet%20access .

Note that you can only follow one of the two guides, not both.

это тоже делалось. просто устанавливается и все. лог загрузки остается тем же

16.01.2011 22:58 #117804

drBatty написал:
а если вы не хотите так, то вам надо установщик поставить сначала:
Install b43-fwcutter

Use version 013 of b43-fwcutter.
Download, extract the b43-fwcutter tarball and build it:

Переключить отображение номеров строк

1 wget http://bu3sch.de/b43/fwcutter/b43-fwcutter-013.tar.bz2
2 tar xjf b43-fwcutter-013.tar.bz2
3 cd b43-fwcutter-013
4 make
5 cd ..

все это проделал. вот лог

root@debian:~# wget http://bu3sch.de/b43/fwcutter/b43-fwcutter-013.tar.bz2
--2011-01-16 22:56:10-- http://bu3sch.de/b43/fwcutter/b43-fwcutter-013.tar.bz2
Распознаётся bu3sch.de... 80.190.117.144
Устанавливается соединение с bu3sch.de|80.190.117.144|:80... соединение установлено.
Запрос HTTP послан, ожидается ответ... 200 OK
Длина: 15359 (15K) [application/x-bzip2]
Saving to: «b43-fwcutter-013.tar.bz2.1»

100%[======================================>] 15 359 --.-K/s в 0,1s

2011-01-16 22:56:11 (141 KB/s) - «b43-fwcutter-013.tar.bz2.1» saved [15359/15359]

root@debian:~# tar xjf b43-fwcutter-013.tar.bz2
root@debian:~# cd b43-fwcutter-013
root@debian:~/b43-fwcutter-013# make
make: Цель `all' не требует выполнения команд.
root@debian:~/b43-fwcutter-013#

16.01.2011 23:01 #117806

сантехник написал:
root@debian:~/b43-fwcutter-013#

ну вот - у вас появился каталог.
там нет этого файла?

16.01.2011 23:02 #117807

drBatty написал:
там нет этого файла?

вот этого: /root/b43-fwcutter-013/b43-fwcutter

16.01.2011 23:15 #117812

сантехник написал:
root@debian:~/b43-fwcutter-013# make
make: Цель `all' не требует выполнения команд.

что-то вы не то сделали :(
[console]~/b43-fwcutter-013$ make
DEPEND dep/md5.d
DEPEND dep/fwcutter.d
CC obj/fwcutter.o
CC obj/md5.o
CC b43-fwcutter
[/console]
и у меня собрался этот файл.

сантехник написал:
Saving to: «b43-fwcutter-013.tar.bz2.1»

скачиваете одно,

сантехник написал:
# tar xjf b43-fwcutter-013.tar.bz2

распаковываете совсем другое.
Будьте внимательнее! Если вы скачали b43-fwcutter-013.tar.bz2.1, то его и надо распаковывать. В следующий раз вы скачаете уже .2...

16.01.2011 23:36 #117830

я прост не понимаю то что я делаю.
вы мне листинг даете, спасибо конечно, но если слепо делать то, что пишут другие, не вникая в саму суть, то какой смысл вообще учиться линуксу?
мне не интересно просто копипастить, меня интересует сама консоль, что пишется и почему.. команды и прочее.
вы не могли бы на пальцах пояснить смысл каждой команды?
понимаю это займет время...

16.01.2011 23:58 #117842

сантехник написал:
мне не интересно просто копипастить, меня интересует сама консоль, что пишется и почему.. команды и прочее.
вы не могли бы на пальцах пояснить смысл каждой команды?

беда в том, что у меня такого девайса нет.

Но в общих чертах суть такова:

1) сначала нужно установить это:

b43-fwcutter is a tool which can extract firmware from various source files.
It's written for BCM43xx driver files.

(надо читать README, пользуясь гугло-переводчиком).
Эта утилитка нужна для извлечения прошивки для драйвера к вашей железке. Как-то так.
1а) Сначала её надо скачать (man wget)
1б) потом распаковать (man tar)
1в) потом собрать (man gcc, man make, это вообще достаточно сложная тема. для программистов. суть в том, что из текстовых файлов на языке С вы собираете исполняемый файл для вашей ОС. Нужно потому, что все ОС разные, и соответственно ваш исполняемый файл не пойдёт для меня. И наоборот. Потому я не могу отдать вам свой файл. Точнее могу конечно, но не факт, что он заработает. Даже скорее не заработает, раз разработчики заставляют собирать юзеров этоу хреновину)

2) теперь вам нужно скачать, распаковать и установить сам драйвер:

This package contains the Broadcom wireless driver, including firmware version 4.178.10.4.

It was extracted out of the GPL source package for Linksys WRT610N.
[url]ftp://ftp.linksys.com/opensourcecode/wrt610n/1.00.00.018/wrt610n_v1.00.00.018_us.tgz[/url]

(вместе с прошивкой).
Это тоже делается в три этапа: закачка и распаковка также как в п1а и п1б, а вот установка с помощью утилиты, которую вы собрали в п1в. Как это делает данная утилита я честно говоря не знаю. Впрочем вам это тоже знать не обязательно. Команда установки у вас есть, и не срабатывала она из-за того, что не было утилиты из п1.

Вот примерно так... Я понимаю, сложно. И вообще-то, по уму, всем этим должны по уму заниматься не вы, а создатели вашего дистрибутива, а ваше дело как пользователя тупо набрать
sudo apt-get ...
эта команда должна (в теории) всё сама скачать и поставить, но что-то не срослось, и вам приходится вот так-вот красноглазить :(

17.01.2011 00:17 #117849

спасибо за детальный ман.
завтра попробую, после того как обожму витую пару и законекчу ноут через eth0, а то надоело бегать м/у двумя компами. сил уже нет )

17.01.2011 00:28 #117857

сантехник написал:
завтра попробую, после того как обожму витую пару и законекчу ноут через eth0, а то надоело бегать м/у двумя компами. сил уже нет )

как-бы с этого и надо было начать... ИМХО этим можно было-бы и закончить :)