mel@dascha-serv:~$ sudo smartctl -a /dev/sda
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Maxtor Fireball 541DX family
Device Model: Maxtor 2B010H1
Serial Number: B18SWD7E
Firmware Version: WAK21R90
User Capacity: 10 246 569 984 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Mon Sep 6 00:27:45 2010 MSD
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 30) seconds.
Offline data collection
capabilities: (0x1b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 13) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
3 Spin_Up_Time 0x0027 234 233 063 Pre-fail Always - 4675
4 Start_Stop_Count 0x0032 253 253 000 Old_age Always - 359
5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail Always - 0
6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline - 0
7 Seek_Error_Rate 0x000a 253 252 000 Old_age Always - 0
8 Seek_Time_Performance 0x0027 248 245 187 Pre-fail Always - 34378
9 Power_On_Minutes 0x0032 250 250 000 Old_age Always - 187h+42m
10 Spin_Retry_Count 0x002b 253 252 157 Pre-fail Always - 0
11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 249 249 000 Old_age Always - 1747
192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always - 85
193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always - 976
194 Unknown_Attribute 0x0032 253 253 000 Old_age Always - 0
195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always - 133
196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline - 0
197 Current_Pending_Sector 0x0008 253 253 000 Old_age Offline - 0
198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0008 199 199 000 Old_age Offline - 0
200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always - 0
201 Soft_Read_Error_Rate 0x000a 253 249 000 Old_age Always - 354
202 TA_Increase_Count 0x000a 253 252 000 Old_age Always - 0
203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always - 0
204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age Always - 0
205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always - 0
207 Spin_High_Current 0x002a 253 252 000 Old_age Always - 0
208 Spin_Buzz 0x002a 253 252 000 Old_age Always - 0
209 Offline_Seek_Performnce 0x0024 253 253 000 Old_age Offline - 0
99 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
100 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
101 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
SMART Error Log Version: 1
Warning: ATA error count 3619 inconsistent with error log pointer 5
ATA Error Count: 3619 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 3619 occurred at disk power-on lifetime: 1195 hours (49 days + 19 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 00 00 00 a0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
a1 00 00 00 00 00 a0 00 00:03:36.880 IDENTIFY PACKET DEVICE
25 00 01 01 00 00 e0 08 00:03:32.528 READ DMA EXT
25 00 01 00 00 00 e0 08 00:03:32.528 READ DMA EXT
25 00 01 00 00 00 e0 08 00:03:32.496 READ DMA EXT
c6 00 10 00 00 00 ef 08 00:03:31.952 SET MULTIPLE MODE
Error 3618 occurred at disk power-on lifetime: 1195 hours (49 days + 19 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 01 3e c5 fa 80
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
f5 00 01 3e c5 fa 80 08 00:03:31.808 SECURITY FREEZE LOCK
42 00 01 3e c5 fa e0 08 00:03:30.960 READ VERIFY SECTOR(S) EXT
e3 00 00 01 00 00 a0 08 00:03:29.936 IDLE
c8 00 01 01 00 00 a0 08 00:03:29.936 READ DMA
ef 03 45 01 4f c2 a0 08 00:03:29.920 SET FEATURES [Set transfer mode]
Error 3617 occurred at disk power-on lifetime: 1195 hours (49 days + 19 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 01 3e c5 fa 80
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
f5 00 01 3e c5 fa 80 08 00:02:25.664 SECURITY FREEZE LOCK
42 00 01 3e c5 fa e0 08 00:02:24.848 READ VERIFY SECTOR(S) EXT
e3 00 00 01 00 00 a0 08 00:02:23.824 IDLE
c8 00 01 01 00 00 a0 08 00:02:23.824 READ DMA
ef 03 45 01 4f c2 a0 08 00:02:23.808 SET FEATURES [Set transfer mode]
Error 3616 occurred at disk power-on lifetime: 1195 hours (49 days + 19 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 3e c5 fa 80
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
f5 00 00 3e c5 fa 80 08 00:02:25.536 SECURITY FREEZE LOCK
42 00 01 3e c5 fa e0 08 00:02:24.832 READ VERIFY SECTOR(S) EXT
e3 00 00 01 00 00 a0 08 00:02:23.808 IDLE
c8 00 01 01 00 00 a0 08 00:02:23.808 READ DMA
ef 03 45 01 4f c2 a0 08 00:02:23.808 SET FEATURES [Set transfer mode]
Error 3615 occurred at disk power-on lifetime: 1194 hours (49 days + 18 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 01 3e c5 fa 80
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
f5 00 01 3e c5 fa 80 08 00:02:25.824 SECURITY FREEZE LOCK
42 00 01 3e c5 fa e0 08 00:02:25.232 READ VERIFY SECTOR(S) EXT
e3 00 00 01 00 00 a0 08 00:02:24.208 IDLE
c8 00 01 01 00 00 a0 08 00:02:24.208 READ DMA
ef 03 45 01 4f c2 a0 08 00:02:24.192 SET FEATURES [Set transfer mode]
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Device does not support Selective Self Tests/Logging
