NP-NC110 Samsung

lspci -k

dmesg

@debian:~$ lspci -k
00:00.0 Host bridge: Intel Corporation N10 Family DMI Bridge
    Subsystem: Samsung Electronics Co Ltd Device c0a8
    Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller: Intel Corporation N10 Family Integrated Graphics Controller
    Subsystem: Samsung Electronics Co Ltd Device c0a8
    Kernel driver in use: i915
00:02.1 Display controller: Intel Corporation N10 Family Integrated Graphics Controller
    Subsystem: Samsung Electronics Co Ltd Device c0a8
00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02)
    Subsystem: Samsung Electronics Co Ltd Device c0a8
    Kernel driver in use: HDA Intel
00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02)
    Kernel driver in use: pcieport
00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 02)
    Kernel driver in use: pcieport
00:1c.2 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 3 (rev 02)
    Kernel driver in use: pcieport
00:1c.3 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 4 (rev 02)
    Kernel driver in use: pcieport
00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 02)
    Subsystem: Samsung Electronics Co Ltd Device c0a8
    Kernel driver in use: uhci_hcd
00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02)
    Subsystem: Samsung Electronics Co Ltd Device c0a8
    Kernel driver in use: uhci_hcd
00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02)
    Subsystem: Samsung Electronics Co Ltd Device c0a8
    Kernel driver in use: uhci_hcd
00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02)
    Subsystem: Samsung Electronics Co Ltd Device c0a8
    Kernel driver in use: uhci_hcd
00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02)
    Subsystem: Samsung Electronics Co Ltd Device c0a8
    Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation NM10 Family LPC Controller (rev 02)
    Subsystem: Samsung Electronics Co Ltd Device c0a8
00:1f.2 SATA controller: Intel Corporation N10/ICH7 Family SATA AHCI Controller (rev 02)
    Subsystem: Samsung Electronics Co Ltd Device c0a8
    Kernel driver in use: ahci
00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 02)
    Subsystem: Samsung Electronics Co Ltd Device c0a8
    Kernel driver in use: i801_smbus
05:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01)
    Subsystem: Wistron NeWeb Corp. Device 051a
09:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05)
    Subsystem: Samsung Electronics Co Ltd Device c0a8
    Kernel driver in use: r8169

[    1.055342] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[    1.055483] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.056167] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
[    1.059538] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.059555] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.059694] mice: PS/2 mouse device common for all mice
[    1.059846] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[    1.059886] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[    1.059913] cpuidle: using governor ladder
[    1.059918] cpuidle: using governor menu
[    1.059927] No iBFT detected.
[    1.060709] TCP cubic registered
[    1.061035] NET: Registered protocol family 10
[    1.062641] Mobile IPv6
[    1.062648] NET: Registered protocol family 17
[    1.062679] Using IPI No-Shortcut mode
[    1.062851] PM: Resume from disk failed.
[    1.062871] registered taskstats version 1
[    1.063500] rtc_cmos 00:04: setting system clock to 2012-08-27 15:33:22 UTC (1346081602)
[    1.063637] Initalizing network drop monitor service
[    1.063686] Freeing unused kernel memory: 380k freed
[    1.063974] Write protecting the kernel text: 2508k
[    1.064039] Write protecting the kernel read-only data: 920k
[    1.092840] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    1.096488] udev[56]: starting version 164
[    1.402600] usbcore: registered new interface driver usbfs
[    1.402657] usbcore: registered new interface driver hub
[    1.402762] usbcore: registered new device driver usb
[    1.449232] SCSI subsystem initialized
[    1.459643] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.459697] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    1.459739] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    1.459748] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    1.459939] thermal LNXTHERM:01: registered as thermal_zone0
[    1.459962] ACPI: Thermal Zone [TZ00] (34 C)
[    1.465041] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[    1.465092] ehci_hcd 0000:00:1d.7: using broken periodic workaround
[    1.465113] ehci_hcd 0000:00:1d.7: debug port 1
[    1.469020] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[    1.469054] ehci_hcd 0000:00:1d.7: irq 23, io mem 0x40e00000
[    1.473062] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    1.473159] r8169 0000:09:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    1.473229] r8169 0000:09:00.0: setting latency timer to 64
[    1.473316] r8169 0000:09:00.0: irq 28 for MSI/MSI-X
[    1.475134] r8169 0000:09:00.0: eth0: RTL8105e at 0xf7f74000, e8:03:9a:94:02:1f, XID 00900000 IRQ 28
[    1.485025] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    1.485080] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.485089] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.485097] usb usb1: Product: EHCI Host Controller
[    1.485104] usb usb1: Manufacturer: Linux 2.6.32-5-686 ehci_hcd
[    1.485111] usb usb1: SerialNumber: 0000:00:1d.7
[    1.485331] usb usb1: configuration #1 chosen from 1 choice
[    1.485426] hub 1-0:1.0: USB hub found
[    1.485446] hub 1-0:1.0: 8 ports detected
[    1.538711] libata version 3.00 loaded.
[    1.547413] uhci_hcd: USB Universal Host Controller Interface driver
[    1.547515] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    1.547535] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    1.547543] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    1.547577] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    1.547623] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001820
[    1.547718] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    1.547727] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.547735] usb usb2: Product: UHCI Host Controller
[    1.547742] usb usb2: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[    1.547749] usb usb2: SerialNumber: 0000:00:1d.0
[    1.548126] usb usb2: configuration #1 chosen from 1 choice
[    1.548323] hub 2-0:1.0: USB hub found
[    1.548345] hub 2-0:1.0: 2 ports detected
[    1.548484] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    1.548503] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    1.548512] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    1.548536] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    1.548596] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001840
[    1.548686] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    1.548694] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.548702] usb usb3: Product: UHCI Host Controller
[    1.548709] usb usb3: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[    1.548716] usb usb3: SerialNumber: 0000:00:1d.1
[    1.549571] usb usb3: configuration #1 chosen from 1 choice
[    1.549828] hub 3-0:1.0: USB hub found
[    1.549853] hub 3-0:1.0: 2 ports detected
[    1.550001] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    1.550020] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    1.550029] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    1.550054] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    1.550115] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001860
[    1.550204] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    1.550213] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.550221] usb usb4: Product: UHCI Host Controller
[    1.550228] usb usb4: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[    1.550235] usb usb4: SerialNumber: 0000:00:1d.2
[    1.551084] usb usb4: configuration #1 chosen from 1 choice
[    1.551340] hub 4-0:1.0: USB hub found
[    1.551364] hub 4-0:1.0: 2 ports detected
[    1.551510] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[    1.551530] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[    1.551539] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    1.551563] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[    1.551626] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001880
[    1.551725] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[    1.551735] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.551742] usb usb5: Product: UHCI Host Controller
[    1.551749] usb usb5: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[    1.551756] usb usb5: SerialNumber: 0000:00:1d.3
[    1.552655] usb usb5: configuration #1 chosen from 1 choice
[    1.552908] hub 5-0:1.0: USB hub found
[    1.552936] hub 5-0:1.0: 2 ports detected
[    1.576359] ahci 0000:00:1f.2: version 3.0
[    1.576395] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    1.576500] ahci 0000:00:1f.2: irq 29 for MSI/MSI-X
[    1.576637] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
[    1.576649] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part 
[    1.576662] ahci 0000:00:1f.2: setting latency timer to 64
[    1.577393] scsi0 : ahci
[    1.577718] scsi1 : ahci
[    1.577918] scsi2 : ahci
[    1.578119] scsi3 : ahci
[    1.578545] ata1: SATA max UDMA/133 abar m1024@0x40e00400 port 0x40e00500 irq 29
[    1.578557] ata2: SATA max UDMA/133 abar m1024@0x40e00400 port 0x40e00580 irq 29
[    1.578567] ata3: SATA max UDMA/133 abar m1024@0x40e00400 port 0x40e00600 irq 29
[    1.578577] ata4: SATA max UDMA/133 abar m1024@0x40e00400 port 0x40e00680 irq 29
[    1.896074] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.896086] ata3: SATA link down (SStatus 0 SControl 300)
[    1.896148] ata4: SATA link down (SStatus 0 SControl 300)
[    1.896154] ata2: SATA link down (SStatus 0 SControl 300)
[    1.896939] ata1.00: ATA-8: Hitachi HTS543225A7A384, ESBOA60W, max UDMA/133
[    1.896952] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    1.897995] ata1.00: configured for UDMA/133
[    1.908046] usb 1-8: new high speed USB device using ehci_hcd and address 3
[    1.912320] scsi 0:0:0:0: Direct-Access     ATA      Hitachi HTS54322 ESBO PQ: 0 ANSI: 5
[    1.927834] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[    1.928099] sd 0:0:0:0: [sda] Write Protect is off
[    1.928109] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.928198] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.928681]  sda: sda1 sda2 < sda5 sda6 >
[    1.991604] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.045195] usb 1-8: New USB device found, idVendor=2232, idProduct=1005
[    2.045208] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.045218] usb 1-8: Product: WebCam SCB-0385N
[    2.045225] usb 1-8: Manufacturer: Image Processor
[    2.045419] usb 1-8: configuration #1 chosen from 1 choice
[    2.284063] usb 3-2: new full speed USB device using uhci_hcd and address 2
[    2.437934] PM: Starting manual resume from disk
[    2.437942] PM: Resume from partition 8:5
[    2.437946] PM: Checking hibernation image.
[    2.460777] usb 3-2: New USB device found, idVendor=0a5c, idProduct=219c
[    2.460788] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    2.460798] usb 3-2: Product: Broadcom BCM2070 Bluetooth Device
[    2.460807] usb 3-2: Manufacturer: Broadcom Corp
[    2.460814] usb 3-2: SerialNumber: 90A4DE1F820F
[    2.461012] usb 3-2: configuration #1 chosen from 1 choice
[    2.462664] PM: Error -22 checking image file
[    2.462672] PM: Resume from disk failed.
[    2.558423] kjournald starting.  Commit interval 5 seconds
[    2.558445] EXT3-fs: mounted filesystem with ordered data mode.
[    4.103781] udev[331]: starting version 164
[    4.496102] ACPI: AC Adapter [ADP1] (off-line)
[    4.638456] ACPI: SSDT 3f5b9797 00203 (v02  PmRef  Cpu0Ist 00003000 INTL 20050624)
[    4.639734] ACPI: SSDT 3f5b8f00 00708 (v02  PmRef  Cpu0Cst 00003001 INTL 20050624)
[    4.718014] Monitor-Mwait will be used to enter C-1 state
[    4.718148] processor LNXCPU:00: registered as cooling_device0
[    4.720533] ACPI: SSDT 3f5b999a 000D4 (v02  PmRef  Cpu1Ist 00003000 INTL 20050624)
[    4.721956] ACPI: SSDT 3f5b9608 00085 (v02  PmRef  Cpu1Cst 00003000 INTL 20050624)
[    4.734269] processor LNXCPU:01: registered as cooling_device1
[    4.735928] input: PC Speaker as /devices/platform/pcspkr/input/input1
[    4.744966] ACPI: Battery Slot [BAT1] (battery present)
[    4.784136] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    4.835834] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input2
[    4.842856] ACPI: Lid Switch [LID0]
[    4.843088] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input3
[    4.843234] ACPI: Power Button [PWRB]
[    4.843413] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input4
[    4.843511] ACPI: Sleep Button [SLPB]
[    4.843694] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input5
[    4.843780] ACPI: Power Button [PWRF]
[    4.981281] Bluetooth: Core ver 2.15
[    4.981424] NET: Registered protocol family 31
[    4.981431] Bluetooth: HCI device and connection manager initialized
[    4.981438] Bluetooth: HCI socket layer initialized
[    5.048153] cfg80211: Using static regulatory domain info
[    5.048161] cfg80211: Regulatory domain: US
[    5.048167]     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    5.048176]     (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
[    5.048185]     (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[    5.048194]     (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[    5.048203]     (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[    5.048212]     (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[    5.048221]     (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
[    5.048947] cfg80211: Calling CRDA for country: US
[    5.093726] Bluetooth: Generic Bluetooth USB driver ver 0.6
[    5.097064] usbcore: registered new interface driver btusb
[    5.102618] Linux video capture interface: v2.00
[    5.176172] [drm] Initialized drm 1.1.0 20060810
[    5.512240] uvcvideo: Found UVC 1.00 device WebCam SCB-0385N (2232:1005)
[    5.513693] input: WebCam SCB-0385N as /devices/pci0000:00/0000:00:1d.7/usb1/1-8/1-8:1.0/input/input6
[    5.513952] usbcore: registered new interface driver uvcvideo
[    5.514492] USB Video Class driver (v0.1.0)
[    5.567991] brcm80211: module is from the staging directory, the quality is unknown, you have been warned.
[    5.585540] brcm80211 0000:05:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    5.585558] brcm80211 0000:05:00.0: setting latency timer to 64
[    5.585641] brcm80211 0000:05:00.0: firmware: requesting brcm/bcm43xx-0.fw
[    5.714702] brcm80211: fail to load firmware brcm/bcm43xx-0.fw
[    5.714711] brcm80211: Failed to find firmware usually in /lib/firmware/brcm
[    5.714761] brcm80211 0000:05:00.0: PCI INT A disabled
[    5.714790] brcm80211: wl_pci_probe: wl_attach failed!
[    5.769251] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    5.769263] i915 0000:00:02.0: setting latency timer to 64
[    5.786410] i915 0000:00:02.0: irq 30 for MSI/MSI-X
[    5.786432] [drm] set up 7M of stolen space
[    5.830084] Synaptics Touchpad, model: 1, fw: 7.5, id: 0x1c0b1, caps: 0xd00033/0x240000/0xa0400
[    5.871772] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input7
[    5.889539] [drm] initialized overlay support
[    6.389055] [drm] Big FIFO is enabled
[    6.389076] [drm] Big FIFO is enabled
[    6.615649] Console: switching to colour frame buffer device 128x37
[    6.623235] fb0: inteldrmfb frame buffer device
[    6.623240] registered panic notifier
[    6.623308] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[    6.623383] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[    6.623453] HDA Intel 0000:00:1b.0: setting latency timer to 64
[    6.848338] hda_codec: ALC269: BIOS auto-probing.
[    6.848929] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input8
[    7.574876] Adding 1998840k swap on /dev/sda5.  Priority:-1 extents:1 across:1998840k 
[    7.879939] EXT3 FS on sda1, internal journal
[    8.004400] loop: module loaded
[    9.207741] fuse init (API version 7.13)
[   10.865799] apm: BIOS not found.
[   11.403157] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input9
[   13.516560] r8169 0000:09:00.0: firmware: requesting rtl_nic/rtl8105e-1.fw
[   13.520456] r8169 0000:09:00.0: eth0: unable to load firmware patch rtl_nic/rtl8105e-1.fw (-2)
[   13.642798] r8169 0000:09:00.0: eth0: link down
[   13.643186] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   16.302484] Bluetooth: L2CAP ver 2.14
[   16.302491] Bluetooth: L2CAP socket layer initialized
[   16.352498] Bluetooth: RFCOMM TTY layer initialized
[   16.352511] Bluetooth: RFCOMM socket layer initialized
[   16.352517] Bluetooth: RFCOMM ver 1.11
[   16.375721] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   16.375729] Bluetooth: BNEP filters: protocol multicast
[   16.436788] Bridge firewalling registered
[   16.500351] Bluetooth: SCO (Voice Link) ver 0.6
[   16.500359] Bluetooth: SCO socket layer initialized
[   17.412409] lp: driver loaded but no devices found
[   17.478141] ppdev: user-space parallel port driver
[   26.625391] CPU0 attaching NULL sched-domain.
[   26.625405] CPU1 attaching NULL sched-domain.
[   26.644143] CPU0 attaching sched-domain:
[   26.644154]  domain 0: span 0-1 level SIBLING
[   26.644162]   groups: group c200370c cpus 0 (cpu_power = 589) group c220370c cpus 1 (cpu_power = 589)
[   26.644183]   domain 1: span 0-1 level MC
[   26.644191]    groups: group c2003778 cpus 0-1 (cpu_power = 1178)
[   26.644207] CPU1 attaching sched-domain:
[   26.644214]  domain 0: span 0-1 level SIBLING
[   26.644221]   groups: group c220370c cpus 1 (cpu_power = 589) group c200370c cpus 0 (cpu_power = 589)
[   26.644240]   domain 1: span 0-1 level MC
[   26.644247]    groups: group c2003778 cpus 0-1 (cpu_power = 1178)
[  245.756847] Monitor-Mwait will be used to enter C-2 state
[  245.756933] Monitor-Mwait will be used to enter C-3 state
[  245.756957] Marking TSC unstable due to TSC halts in idle
[  245.757570] Switching to clocksource hpet
[ 1338.960121] usb 1-3: new high speed USB device using ehci_hcd and address 4
[ 1339.135097] usb 1-3: New USB device found, idVendor=8564, idProduct=1000
[ 1339.135110] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1339.135120] usb 1-3: Product: Mass Storage Device
[ 1339.135128] usb 1-3: Manufacturer: JetFlash
[ 1339.135136] usb 1-3: SerialNumber: 3829XRKNOUARND2C
[ 1339.135433] usb 1-3: configuration #1 chosen from 1 choice
[ 1339.907389] usb 1-3: USB disconnect, address 4
[ 1341.116048] Initializing USB Mass Storage driver...
[ 1341.116323] usbcore: registered new interface driver usb-storage
[ 1341.116336] USB Mass Storage support registered.
[ 1350.276144] usb 1-1: new high speed USB device using ehci_hcd and address 5
[ 1350.451098] usb 1-1: New USB device found, idVendor=8564, idProduct=1000
[ 1350.451111] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1350.451121] usb 1-1: Product: Mass Storage Device
[ 1350.451129] usb 1-1: Manufacturer: JetFlash
[ 1350.451137] usb 1-1: SerialNumber: 3829XRKNOUARND2C
[ 1350.451431] usb 1-1: configuration #1 chosen from 1 choice
[ 1350.452168] scsi4 : SCSI emulation for USB Mass Storage devices
[ 1350.452919] usb-storage: device found at 5
[ 1350.452930] usb-storage: waiting for device to settle before scanning
[ 1352.125072] usb 1-1: USB disconnect, address 5
[ 1352.460130] usb 1-1: new high speed USB device using ehci_hcd and address 6
[ 1352.635096] usb 1-1: New USB device found, idVendor=8564, idProduct=1000
[ 1352.635110] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1352.635120] usb 1-1: Product: Mass Storage Device
[ 1352.635127] usb 1-1: Manufacturer: JetFlash
[ 1352.635135] usb 1-1: SerialNumber: 3829XRKNOUARND2C
[ 1352.635430] usb 1-1: configuration #1 chosen from 1 choice
[ 1352.636152] scsi5 : SCSI emulation for USB Mass Storage devices
[ 1352.636907] usb-storage: device found at 6
[ 1352.636918] usb-storage: waiting for device to settle before scanning
[ 1357.048073] usb 1-1: USB disconnect, address 6
[ 1359.636127] usb 1-1: new high speed USB device using ehci_hcd and address 7
[ 1359.811097] usb 1-1: New USB device found, idVendor=8564, idProduct=1000
[ 1359.811110] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1359.811120] usb 1-1: Product: Mass Storage Device
[ 1359.811127] usb 1-1: Manufacturer: JetFlash
[ 1359.811135] usb 1-1: SerialNumber: 3829XRKNOUARND2C
[ 1359.811431] usb 1-1: configuration #1 chosen from 1 choice
[ 1359.813123] scsi6 : SCSI emulation for USB Mass Storage devices
[ 1359.813857] usb-storage: device found at 7
[ 1359.813868] usb-storage: waiting for device to settle before scanning
[ 1360.649443] usb 1-1: USB disconnect, address 7
[ 1361.156138] usb 1-1: new high speed USB device using ehci_hcd and address 8
[ 1361.331098] usb 1-1: New USB device found, idVendor=8564, idProduct=1000
[ 1361.331111] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1361.331121] usb 1-1: Product: Mass Storage Device
[ 1361.331129] usb 1-1: Manufacturer: JetFlash
[ 1361.331136] usb 1-1: SerialNumber: 3829XRKNOUARND2C
[ 1361.331431] usb 1-1: configuration #1 chosen from 1 choice
[ 1361.333358] scsi7 : SCSI emulation for USB Mass Storage devices
[ 1361.334085] usb-storage: device found at 8
[ 1361.334096] usb-storage: waiting for device to settle before scanning
[ 1366.332354] usb-storage: device scan complete
[ 1366.621309] scsi 7:0:0:0: Direct-Access     JetFlash Transcend 2GB    1100 PQ: 0 ANSI: 0 CCS
[ 1366.624911] sd 7:0:0:0: [sdb] 3932160 512-byte logical blocks: (2.01 GB/1.87 GiB)
[ 1366.625760] sd 7:0:0:0: [sdb] Write Protect is off
[ 1366.625778] sd 7:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 1366.625790] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[ 1366.629895] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[ 1366.629915]  sdb: sdb1
[ 1366.637735] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[ 1366.637748] sd 7:0:0:0: [sdb] Attached SCSI removable disk
[ 1367.242966] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 1401.298450] usb 1-1: USB disconnect, address 8
[ 1456.404135] usb 1-1: new high speed USB device using ehci_hcd and address 9
[ 1456.579109] usb 1-1: New USB device found, idVendor=8564, idProduct=1000
[ 1456.579123] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1456.579133] usb 1-1: Product: Mass Storage Device
[ 1456.579140] usb 1-1: Manufacturer: JetFlash
[ 1456.579148] usb 1-1: SerialNumber: 3829XRKNOUARND2C
[ 1456.579442] usb 1-1: configuration #1 chosen from 1 choice
[ 1456.580138] scsi8 : SCSI emulation for USB Mass Storage devices
[ 1456.580880] usb-storage: device found at 9
[ 1456.580891] usb-storage: waiting for device to settle before scanning
[ 1461.580526] usb-storage: device scan complete
[ 1461.874572] scsi 8:0:0:0: Direct-Access     JetFlash Transcend 2GB    1100 PQ: 0 ANSI: 0 CCS
[ 1461.878669] sd 8:0:0:0: [sdc] 3932160 512-byte logical blocks: (2.01 GB/1.87 GiB)
[ 1461.880030] sd 8:0:0:0: [sdc] Write Protect is off
[ 1461.880047] sd 8:0:0:0: [sdc] Mode Sense: 43 00 00 00
[ 1461.880059] sd 8:0:0:0: [sdc] Assuming drive cache: write through
[ 1461.886076] sd 8:0:0:0: [sdc] Assuming drive cache: write through
[ 1461.886097]  sdc: sdc1
[ 1461.891884] sd 8:0:0:0: [sdc] Assuming drive cache: write through
[ 1461.891895] sd 8:0:0:0: [sdc] Attached SCSI removable disk
[ 1462.504408] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 1726.296144] usb 3-1: new full speed USB device using uhci_hcd and address 3
[ 1726.535183] usb 3-1: New USB device found, idVendor=04fc, idProduct=0801
[ 1726.535196] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1726.535207] usb 3-1: Product: USB Multi-Smart Mouse
[ 1726.535214] usb 3-1: Manufacturer: MLK
[ 1726.535493] usb 3-1: configuration #1 chosen from 1 choice
[ 1726.645924] usbcore: registered new interface driver hiddev
[ 1726.650501] input: MLK USB Multi-Smart Mouse as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input10
[ 1726.651180] generic-usb 0003:04FC:0801.0001: input,hidraw0: USB HID v1.11 Mouse [MLK USB Multi-Smart Mouse] on usb-0000:00:1d.1-1/input0
[ 1726.651292] usbcore: registered new interface driver usbhid
[ 1726.651309] usbhid: v2.6:USB HID core driver
[ 2151.090374] nm-connection-e[2565]: segfault at 2c ip 08073c24 sp bfef9b90 error 4 in nm-connection-editor[8048000+56000]
[ 2168.754140] r8169 0000:09:00.0: eth0: link up
[ 2168.754766] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 2179.361029] eth0: no IPv6 routers present
[ 2510.622658] usb 1-1: USB disconnect, address 9
[ 2555.700145] usb 1-1: new high speed USB device using ehci_hcd and address 11
[ 2555.875125] usb 1-1: New USB device found, idVendor=8564, idProduct=1000
[ 2555.875138] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2555.875148] usb 1-1: Product: Mass Storage Device
[ 2555.875156] usb 1-1: Manufacturer: JetFlash
[ 2555.875163] usb 1-1: SerialNumber: 3829XRKNOUARND2C
[ 2555.875459] usb 1-1: configuration #1 chosen from 1 choice
[ 2555.876133] scsi9 : SCSI emulation for USB Mass Storage devices
[ 2555.876869] usb-storage: device found at 11
[ 2555.876879] usb-storage: waiting for device to settle before scanning
[ 2560.876372] usb-storage: device scan complete
[ 2561.176311] scsi 9:0:0:0: Direct-Access     JetFlash Transcend 2GB    1100 PQ: 0 ANSI: 0 CCS
[ 2561.185084] sd 9:0:0:0: [sdc] 3932160 512-byte logical blocks: (2.01 GB/1.87 GiB)
[ 2561.186021] sd 9:0:0:0: [sdc] Write Protect is off
[ 2561.186033] sd 9:0:0:0: [sdc] Mode Sense: 43 00 00 00
[ 2561.186040] sd 9:0:0:0: [sdc] Assuming drive cache: write through
[ 2561.189530] sd 9:0:0:0: [sdc] Assuming drive cache: write through
[ 2561.189544]  sdc: sdc1
[ 2561.193464] sd 9:0:0:0: [sdc] Assuming drive cache: write through
[ 2561.193477] sd 9:0:0:0: [sdc] Attached SCSI removable disk
[ 2563.141551] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 2888.278258] usb 1-1: USB disconnect, address 11
[ 2939.604141] usb 1-1: new high speed USB device using ehci_hcd and address 12
[ 2939.779174] usb 1-1: New USB device found, idVendor=8564, idProduct=1000
[ 2939.779186] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2939.779197] usb 1-1: Product: Mass Storage Device
[ 2939.779204] usb 1-1: Manufacturer: JetFlash
[ 2939.779212] usb 1-1: SerialNumber: 3829XRKNOUARND2C
[ 2939.779510] usb 1-1: configuration #1 chosen from 1 choice
[ 2939.780210] scsi10 : SCSI emulation for USB Mass Storage devices
[ 2939.780950] usb-storage: device found at 12
[ 2939.780961] usb-storage: waiting for device to settle before scanning
[ 2944.781248] usb-storage: device scan complete
[ 2945.083019] scsi 10:0:0:0: Direct-Access     JetFlash Transcend 2GB    1100 PQ: 0 ANSI: 0 CCS
[ 2945.087586] sd 10:0:0:0: [sdc] 3932160 512-byte logical blocks: (2.01 GB/1.87 GiB)
[ 2945.088470] sd 10:0:0:0: [sdc] Write Protect is off
[ 2945.088486] sd 10:0:0:0: [sdc] Mode Sense: 43 00 00 00
[ 2945.088495] sd 10:0:0:0: [sdc] Assuming drive cache: write through
[ 2945.092321] sd 10:0:0:0: [sdc] Assuming drive cache: write through
[ 2945.092342]  sdc: sdc1
[ 2945.097598] sd 10:0:0:0: [sdc] Assuming drive cache: write through
[ 2945.097619] sd 10:0:0:0: [sdc] Attached SCSI removable disk
[ 2945.567854] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 2967.120634] FAT: Directory bread(block 8192) failed
[ 2967.120646] FAT: Directory bread(block 8193) failed
[ 2967.120654] FAT: Directory bread(block 8194) failed
[ 2967.120662] FAT: Directory bread(block 8195) failed
[ 2967.120670] FAT: Directory bread(block 8196) failed
[ 2967.120679] FAT: Directory bread(block 8197) failed
[ 2967.120687] FAT: Directory bread(block 8198) failed
[ 2967.120695] FAT: Directory bread(block 8199) failed
[ 2967.143310] FAT: Directory bread(block 8192) failed
[ 2967.143322] FAT: Directory bread(block 8193) failed
[ 2967.143330] FAT: Directory bread(block 8194) failed
[ 2967.143337] FAT: Directory bread(block 8195) failed
[ 2967.143345] FAT: Directory bread(block 8196) failed
[ 2967.143353] FAT: Directory bread(block 8197) failed
[ 2967.143360] FAT: Directory bread(block 8198) failed
[ 2967.143368] FAT: Directory bread(block 8199) failed
[ 2967.143424] FAT: Directory bread(block 8192) failed
[ 2967.143433] FAT: Directory bread(block 8193) failed
[ 2967.143441] FAT: Directory bread(block 8194) failed
[ 2967.143450] FAT: Directory bread(block 8195) failed
[ 2967.143458] FAT: Directory bread(block 8196) failed
[ 2967.143467] FAT: Directory bread(block 8197) failed
[ 2967.143475] FAT: Directory bread(block 8198) failed
[ 2967.143483] FAT: Directory bread(block 8199) failed
[ 2967.143531] FAT: Directory bread(block 8192) failed
[ 2967.143540] FAT: Directory bread(block 8193) failed
[ 2967.143548] FAT: Directory bread(block 8194) failed
[ 2967.143556] FAT: Directory bread(block 8195) failed
[ 2967.143564] FAT: Directory bread(block 8196) failed
[ 2967.143573] FAT: Directory bread(block 8197) failed
[ 2967.143580] FAT: Directory bread(block 8198) failed
[ 2967.143588] FAT: Directory bread(block 8199) failed
[ 2971.165549] FAT: Directory bread(block 8192) failed
[ 2971.165563] FAT: Directory bread(block 8193) failed
[ 2971.165572] FAT: Directory bread(block 8194) failed
[ 2971.165581] FAT: Directory bread(block 8195) failed
[ 2971.165589] FAT: Directory bread(block 8196) failed
[ 2971.165598] FAT: Directory bread(block 8197) failed
[ 2971.165606] FAT: Directory bread(block 8198) failed
[ 2971.165615] FAT: Directory bread(block 8199) failed
[ 4477.262558] nautilus: sending ioctl 2285 to a partition!
[ 5758.360748] [drm] Big FIFO is enabled
[ 6829.544550] [drm] Big FIFO is enabled
[ 7537.364915] [drm] Big FIFO is enabled
[ 9045.133797] [drm] Big FIFO is enabled