LinuxForum.Fans
Тема

Включение Wi-Fi на EeePC-900HA - "устройство не готово"

Автор: vlav 38 сообщений 16515 просмотров
19.01.2011 02:28 · отредактировано #118512

Доброе время суток!
Есть проблема с использованием сочетания клавиш Fn-F2 на нетбуке EeePC-900HA для включения/отключения Wi-Fi.
Wi-Fi благополучно отключается, но обратно не включается, хотя светодиод Wi-Fi зажигается. NetworkManager пишет "Устройство не готово". Wi-Fi запускается только после перезагрузки, причем, если перезагружаться с выключенным Wi-Fi (с негорящим индикатором), то после перезагрузки Wi-Fi также не стартует.

Нетбук EeePC-900HA, дистрибутив Debian Squeeze.

На Ubuntu (после включения pciehp.pciehp_force=1 в параметры загрузки) такой проблемы нет!

Камрады, есть идеи?

19.01.2011 06:37 #118514

Какая версия ядра?
Попробуйте обновить ядро до последнего (в Мандриве помогло в подобной ситуации)

19.01.2011 21:40 #118732
D_Chu написал:
Какая версия ядра?
Попробуйте обновить ядро до последнего (в Мандриве помогло в подобной ситуации)

Ядро штатное - 2.6.32-5

Пробовал, подключив дополнительные репозитории, ставить и 36-е ядро из Aptosid и из Ubuntu, и даже 37-е из ветки Experimental - без результатов.
Боюсь, дело не в ядре.

19.01.2011 21:49 · отредактировано #118736
vlav написал:
Пробовал, подключив дополнительные репозитории, ставить и 36-е ядро из Aptosid и из Ubuntu, и даже 37-е из ветки Experimental - без результатов.
Боюсь, дело не в ядре.

wi-fi на чипе atheros?
Драйвера для wi-fi из репозитория или сами собирали? (извините, не знаю, что именно есть в репах Дебиана, потому и спрашиваю)
Если собирали, пробовали пересобирать драйвера с новым ядром?

19.01.2011 23:13 #118750

Wi-Fi - да, на чипе Atheros.
Драйвер специально не собирал, карта поддерживается по-умолчанию.

20.01.2011 06:25 #118791

Тогда мысли закончились :(. Может, кто другой что подскажет.

20.01.2011 08:39 · отредактировано #118800

Попробуй установить пакет eeepc-acpi-scripts, может поможет.

20.01.2011 23:40 #119159
text
ifconfig
iwconfig
route

показываем пожалуйста.

21.01.2011 00:34 #119174

Привожу вывод терминала.
Подключение только по Wi-Fi.

1. Нормальная работа (до нажатия Fn-F2)
1.1. ifconfig

text

eth0      Link encap:Ethernet  HWaddr e0:cb:4e:05:b8:d0  
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:1
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:27 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:344 errors:0 dropped:0 overruns:0 frame:0
          TX packets:344 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:27456 (26.8 KiB)  TX bytes:27456 (26.8 KiB)


wlan0     Link encap:Ethernet  HWaddr 00:25:d3:d2:ba:c9  
          inet addr:192.168.1.5  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::225:d3ff:fed2:bac9/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:371 errors:0 dropped:0 overruns:0 frame:0
          TX packets:355 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:306587 (299.4 KiB)  TX bytes:99676 (97.3 KiB)

1.2. iwconfig

text

lo        no wireless extensions.

eth0      no wireless extensions.


wlan0     IEEE 802.11bg  ESSID:"ValsNet"  
          Mode:Managed  Frequency:2.412 GHz  Access Point: 00:22:3F:88:53:CA   
          Bit Rate=36 Mb/s   Tx-Power=20 dBm   
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
          Link Quality=35/70  Signal level=-75 dBm  
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0


pan0      no wireless extensions.

1.3. route

text

Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.168.1.0     *               255.255.255.0   U     2      0        0 wlan0
default         192.168.1.1     0.0.0.0         UG    0      0        0 wlan0

2. После двухкратного нажатия fn-f2
2.1. ifconfig

text
 
eth0      Link encap:Ethernet  HWaddr e0:cb:4e:05:b8:d0  
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:1
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:27 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:344 errors:0 dropped:0 overruns:0 frame:0
          TX packets:344 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:27456 (26.8 KiB)  TX bytes:27456 (26.8 KiB)

2.2. iwconfig

text

lo        no wireless extensions.

eth0      no wireless extensions.


wlan0     IEEE 802.11bg  ESSID:off/any  
          Mode:Managed  Frequency:2.412 GHz  Access Point: Not-Associated   
          Tx-Power=20 dBm   
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
          
pan0      no wireless extensions.

2.3. route

text

Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
21.01.2011 00:52 #119182

vlav, установите пакет wicd, запустите, в настройках укажите интерфейс для wifi интерфейса wlan0.
и удалите к чёрту нетворк менеджер.

21.01.2011 00:52 #119183
system-root написал:
vlav, установите пакет wicd, запустите, в настройках укажите для wifi интерфейса wlan0.
и удалите к чёрту нетворк менеджер.
21.01.2011 01:13 #119195

system-root написал:
[quote=system-root]vlav, установите пакет wicd, запустите, в настройках укажите для wifi интерфейса wlan0.
и удалите к чёрту нетворк менеджер.
[/quote]

Счастья это, увы, не приносит: вместо "Устройство не готово" (NetworkManager) можно лицезреть "Беспроводные сети не найдены" (Wicd).
21.01.2011 01:15 · отредактировано #119196

vlav, dmesg и lspci -vvv под споилером покажите

21.01.2011 01:30 #119200

1. dmesq

text

[    0.200225] pci 0000:00:02.0: reg 18 32bit mmio pref: [0xd0000000-0xdfffffff]
[    0.200235] pci 0000:00:02.0: reg 1c 32bit mmio: [0xf3dc0000-0xf3dfffff]
[    0.200287] pci 0000:00:02.1: reg 10 32bit mmio: [0xf3e80000-0xf3efffff]
[    0.200426] pci 0000:00:1b.0: reg 10 64bit mmio: [0xf3db8000-0xf3dbbfff]
[    0.200501] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.200510] pci 0000:00:1b.0: PME# disabled
[    0.200623] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.200631] pci 0000:00:1c.0: PME# disabled
[    0.200749] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    0.200757] pci 0000:00:1c.1: PME# disabled
[    0.200875] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[    0.200883] pci 0000:00:1c.3: PME# disabled
[    0.200967] pci 0000:00:1d.0: reg 20 io port: [0xc400-0xc41f]
[    0.201049] pci 0000:00:1d.1: reg 20 io port: [0xc480-0xc49f]
[    0.201130] pci 0000:00:1d.2: reg 20 io port: [0xc800-0xc81f]
[    0.201212] pci 0000:00:1d.3: reg 20 io port: [0xc880-0xc89f]
[    0.201298] pci 0000:00:1d.7: reg 10 32bit mmio: [0xf3db7c00-0xf3db7fff]
[    0.201374] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.201382] pci 0000:00:1d.7: PME# disabled
[    0.201578] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
[    0.201587] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO
[    0.201595] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0380 (mask 0003)
[    0.201604] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0290 (mask 0007)
[    0.201612] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 0068 (mask 0003)
[    0.201692] pci 0000:00:1f.2: reg 10 io port: [0x00-0x07]
[    0.201705] pci 0000:00:1f.2: reg 14 io port: [0x00-0x03]
[    0.201717] pci 0000:00:1f.2: reg 18 io port: [0x00-0x07]
[    0.201729] pci 0000:00:1f.2: reg 1c io port: [0x00-0x03]
[    0.201742] pci 0000:00:1f.2: reg 20 io port: [0xffa0-0xffaf]
[    0.201786] pci 0000:00:1f.2: PME# supported from D3hot
[    0.201794] pci 0000:00:1f.2: PME# disabled
[    0.201977] pci 0000:02:00.0: reg 10 64bit mmio: [0xfbff0000-0xfbffffff]
[    0.202124] pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.202234] pci 0000:00:1c.1: bridge io port: [0xe000-0xefff]
[    0.202243] pci 0000:00:1c.1: bridge 32bit mmio: [0xf4000000-0xfbffffff]
[    0.202256] pci 0000:00:1c.1: bridge 64bit mmio pref: [0xec000000-0xf2ffffff]
[    0.202342] pci 0000:01:00.0: reg 10 64bit mmio: [0xf3fc0000-0xf3ffffff]
[    0.202358] pci 0000:01:00.0: reg 18 io port: [0xdc00-0xdc7f]
[    0.202450] pci 0000:01:00.0: PME# supported from D3hot D3cold
[    0.202459] pci 0000:01:00.0: PME# disabled
[    0.202510] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.202618] pci 0000:00:1c.3: bridge io port: [0xd000-0xdfff]
[    0.202627] pci 0000:00:1c.3: bridge 32bit mmio: [0xf3f00000-0xf3ffffff]
[    0.202705] pci 0000:00:1e.0: transparent bridge
[    0.202751] pci_bus 0000:00: on NUMA node 0
[    0.202763] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.203100] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
[    0.203194] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT]
[    0.225417] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[    0.225657] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[    0.225888] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 *7 10 11 12 14 15)
[    0.226121] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[    0.226352] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[    0.226588] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[    0.226820] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 *4 5 6 7 10 11 12 14 15)
[    0.227051] ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 10 11 12 14 15)
[    0.227271] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[    0.227293] vgaarb: loaded
[    0.227337] PCI: Using ACPI for IRQ routing
[    0.227337] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.227337] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[    0.232027] Switching to clocksource tsc
[    0.234220] pnp: PnP ACPI init
[    0.234256] ACPI: bus type pnp registered
[    0.237990] pnp: PnP ACPI: found 13 devices
[    0.237997] ACPI: ACPI bus type pnp unregistered
[    0.238005] PnPBIOS: Disabled by ACPI PNP
[    0.238030] system 00:01: iomem range 0xfed13000-0xfed19fff has been reserved
[    0.238050] system 00:08: ioport range 0x25c-0x25f has been reserved
[    0.238058] system 00:08: ioport range 0x380-0x383 has been reserved
[    0.238065] system 00:08: ioport range 0x400-0x41f has been reserved
[    0.238072] system 00:08: ioport range 0x4d0-0x4d1 has been reserved
[    0.238080] system 00:08: ioport range 0x800-0x87f has been reserved
[    0.238087] system 00:08: ioport range 0x480-0x4bf has been reserved
[    0.238095] system 00:08: iomem range 0x8c000000-0x8c01ffff has been reserved
[    0.238103] system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
[    0.238111] system 00:08: iomem range 0xfed20000-0xfed3ffff has been reserved
[    0.238119] system 00:08: iomem range 0xfed50000-0xfed8ffff has been reserved
[    0.238127] system 00:08: iomem range 0xffb00000-0xffbfffff has been reserved
[    0.238135] system 00:08: iomem range 0xfff00000-0xffffffff could not be reserved
[    0.238149] system 00:0a: iomem range 0xfec00000-0xfec00fff could not be reserved
[    0.238157] system 00:0a: iomem range 0xfee00000-0xfee00fff has been reserved
[    0.238170] system 00:0b: iomem range 0xe0000000-0xe3ffffff has been reserved
[    0.238183] system 00:0c: iomem range 0x0-0x9ffff could not be reserved
[    0.238191] system 00:0c: iomem range 0xc0000-0xcffff could not be reserved
[    0.238198] system 00:0c: iomem range 0xe0000-0xfffff could not be reserved
[    0.238206] system 00:0c: iomem range 0x100000-0x3f7fffff could not be reserved
[    0.273310] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:04
[    0.273319] pci 0000:00:1c.0:   IO window: 0x1000-0x1fff
[    0.273330] pci 0000:00:1c.0:   MEM window: 0x40000000-0x401fffff
[    0.273340] pci 0000:00:1c.0:   PREFETCH window: 0x00000040200000-0x000000403fffff
[    0.273353] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:02
[    0.273360] pci 0000:00:1c.1:   IO window: 0xe000-0xefff
[    0.273370] pci 0000:00:1c.1:   MEM window: 0xf4000000-0xfbffffff
[    0.273379] pci 0000:00:1c.1:   PREFETCH window: 0x000000ec000000-0x000000f2ffffff
[    0.273392] pci 0000:00:1c.3: PCI bridge, secondary bus 0000:01
[    0.273399] pci 0000:00:1c.3:   IO window: 0xd000-0xdfff
[    0.273409] pci 0000:00:1c.3:   MEM window: 0xf3f00000-0xf3ffffff
[    0.273418] pci 0000:00:1c.3:   PREFETCH window: 0x00000040400000-0x000000405fffff
[    0.273431] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05
[    0.273436] pci 0000:00:1e.0:   IO window: disabled
[    0.273445] pci 0000:00:1e.0:   MEM window: disabled
[    0.273453] pci 0000:00:1e.0:   PREFETCH window: disabled
[    0.273478] pci 0000:00:1c.0: enabling device (0104 -> 0107)
[    0.273497] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.273507] pci 0000:00:1c.0: setting latency timer to 64
[    0.273527] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    0.273536] pci 0000:00:1c.1: setting latency timer to 64
[    0.273554] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[    0.273563] pci 0000:00:1c.3: setting latency timer to 64
[    0.273576] pci 0000:00:1e.0: setting latency timer to 64
[    0.273586] pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
[    0.273592] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[    0.273599] pci_bus 0000:04: resource 0 io:  [0x1000-0x1fff]
[    0.273605] pci_bus 0000:04: resource 1 mem: [0x40000000-0x401fffff]
[    0.273612] pci_bus 0000:04: resource 2 pref mem [0x40200000-0x403fffff]
[    0.273619] pci_bus 0000:02: resource 0 io:  [0xe000-0xefff]
[    0.273625] pci_bus 0000:02: resource 1 mem: [0xf4000000-0xfbffffff]
[    0.273632] pci_bus 0000:02: resource 2 pref mem [0xec000000-0xf2ffffff]
[    0.273638] pci_bus 0000:01: resource 0 io:  [0xd000-0xdfff]
[    0.273645] pci_bus 0000:01: resource 1 mem: [0xf3f00000-0xf3ffffff]
[    0.273652] pci_bus 0000:01: resource 2 pref mem [0x40400000-0x405fffff]
[    0.273658] pci_bus 0000:05: resource 3 io:  [0x00-0xffff]
[    0.273665] pci_bus 0000:05: resource 4 mem: [0x000000-0xffffffff]
[    0.273732] NET: Registered protocol family 2
[    0.273917] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.274557] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.275536] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.276045] TCP: Hash tables configured (established 131072 bind 65536)
[    0.276053] TCP reno registered
[    0.276264] NET: Registered protocol family 1
[    0.276322] pci 0000:00:02.0: Boot video device
[    0.276560] Unpacking initramfs...
[    0.427978] Freeing initrd memory: 3371k freed
[    0.431894] audit: initializing netlink socket (disabled)
[    0.431919] type=2000 audit(1295561648.431:1): initialized
[    0.437798] highmem bounce pool size: 64 pages
[    0.437811] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    0.441073] VFS: Disk quotas dquot_6.5.2
[    0.441198] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.441356] msgmni has been set to 1738
[    0.441778] alg: No test for stdrng (krng)
[    0.441900] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.441907] io scheduler noop registered
[    0.441911] io scheduler anticipatory registered
[    0.441916] io scheduler deadline registered
[    0.442006] io scheduler cfq registered (default)
[    0.442238] pcieport 0000:00:1c.0: irq 24 for MSI/MSI-X
[    0.442255] pcieport 0000:00:1c.0: setting latency timer to 64
[    0.442488] pcieport 0000:00:1c.1: irq 25 for MSI/MSI-X
[    0.442503] pcieport 0000:00:1c.1: setting latency timer to 64
[    0.442728] pcieport 0000:00:1c.3: irq 26 for MSI/MSI-X
[    0.442744] pcieport 0000:00:1c.3: setting latency timer to 64
[    0.443091] isapnp: Scanning for PnP cards...
[    0.796803] isapnp: No Plug & Play device found
[    0.800212] Linux agpgart interface v0.103
[    0.800360] agpgart-intel 0000:00:00.0: Intel 945GME Chipset
[    0.800548] agpgart-intel 0000:00:00.0: detected 7932K stolen memory
[    0.803194] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[    0.803346] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.804133] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    0.829762] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.829782] serio: i8042 AUX port at 0x60,0x64 irq 12
[    0.829940] mice: PS/2 mouse device common for all mice
[    0.830025] rtc_cmos 00:03: RTC can wake from S4
[    0.830127] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    0.830178] rtc0: alarms up to one month, 114 bytes nvram, hpet irqs
[    0.830211] cpuidle: using governor ladder
[    0.830217] cpuidle: using governor menu
[    0.830229] No iBFT detected.
[    0.831242] TCP cubic registered
[    0.831684] NET: Registered protocol family 10
[    0.832743] lo: Disabled Privacy Extensions
[    0.833444] Mobile IPv6
[    0.833450] NET: Registered protocol family 17
[    0.833481] Using IPI No-Shortcut mode
[    0.833653] PM: Resume from disk failed.
[    0.833674] registered taskstats version 1
[    0.834234] rtc_cmos 00:03: setting system clock to 2011-01-20 22:14:09 UTC (1295561649)
[    0.834301] Initalizing network drop monitor service
[    0.834361] Freeing unused kernel memory: 376k freed
[    0.834664] Write protecting the kernel text: 2504k
[    0.834705] Write protecting the kernel read-only data: 920k
[    0.857477] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    0.962355] udev[59]: starting version 164
[    1.248072] SCSI subsystem initialized
[    1.277787] thermal LNXTHERM:01: registered as thermal_zone0
[    1.277816] ACPI: Thermal Zone [TZ00] (56 C)
[    1.309861] libata version 3.00 loaded.
[    1.318942] ata_piix 0000:00:1f.2: version 2.13
[    1.318985] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    1.319000] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
[    1.319094] ata_piix 0000:00:1f.2: setting latency timer to 64
[    1.319269] scsi0 : ata_piix
[    1.319540] scsi1 : ata_piix
[    1.322471] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[    1.322481] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[    1.522161] ata1.00: ATA-8: ST9160301AS, 0001SDM2, max UDMA/133
[    1.522169] ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    1.536752] ata1.00: configured for UDMA/133
[    1.536980] scsi 0:0:0:0: Direct-Access     ATA      ST9160301AS      0001 PQ: 0 ANSI: 5
[    1.556965] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[    1.557213] sd 0:0:0:0: [sda] Write Protect is off
[    1.557223] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.557319] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.557862]  sda: sda1 sda2 < sda5 >
[    1.565251] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.886164] device-mapper: uevent: version 1.0.3
[    1.886588] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[   20.860974] PM: Starting manual resume from disk
[   20.860984] PM: Resume from partition 254:2
[   20.860988] PM: Checking hibernation image.
[   20.861669] PM: Error -22 checking image file
[   20.861674] PM: Resume from disk failed.
[   20.875736] JFS: nTxBlock = 8008, nTxLock = 64065
[   24.352422] udev[365]: starting version 164
[   25.277561] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1
[   25.282799] ACPI: Lid Switch [LID]
[   25.283059] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2
[   25.283075] ACPI: Sleep Button [SLPB]
[   25.283261] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input3
[   25.283274] ACPI: Power Button [PWRB]
[   25.283464] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[   25.283476] ACPI: Power Button [PWRF]
[   25.304349] ACPI: SSDT 3f7ae180 0023C (v01  PmRef  Cpu0Ist 00003000 INTL 20051117)
[   25.305733] ACPI: SSDT 3f7ae450 00724 (v01  PmRef  Cpu0Cst 00003001 INTL 20051117)
[   25.309426] Monitor-Mwait will be used to enter C-1 state
[   25.309516] Monitor-Mwait will be used to enter C-2 state
[   25.309591] Monitor-Mwait will be used to enter C-3 state
[   25.309610] Marking TSC unstable due to TSC halts in idle
[   25.309894] processor LNXCPU:00: registered as cooling_device0
[   25.311001] ACPI: SSDT 3f7ae0b0 000CC (v01  PmRef  Cpu1Ist 00003000 INTL 20051117)
[   25.312341] ACPI: SSDT 3f7ae3c0 00085 (v01  PmRef  Cpu1Cst 00003000 INTL 20051117)
[   25.312732] Switching to clocksource hpet
[   25.313784] processor LNXCPU:01: registered as cooling_device1
[   25.482610] usbcore: registered new interface driver usbfs
[   25.483272] usbcore: registered new interface driver hub
[   25.483998] usbcore: registered new device driver usb
[   25.547882] ACPI: AC Adapter [AC0] (off-line)
[   25.681900] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   25.689689] ATL1E 0000:01:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[   25.689793] ATL1E 0000:01:00.0: setting latency timer to 64
[   25.720988] ACPI: Battery Slot [BAT0] (battery present)
[   25.725303] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input5
[   25.725439] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[   25.801446] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   25.801535] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[   25.801587] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[   25.801597] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[   25.801660] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[   25.801716] ehci_hcd 0000:00:1d.7: using broken periodic workaround
[   25.801739] ehci_hcd 0000:00:1d.7: debug port 1
[   25.805651] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[   25.805809] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf3db7c00
[   25.809771] intel_rng: FWH not detected
[   25.821190] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[   25.821314] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[   25.821324] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   25.821333] usb usb1: Product: EHCI Host Controller
[   25.821341] usb usb1: Manufacturer: Linux 2.6.32-5-686 ehci_hcd
[   25.821349] usb usb1: SerialNumber: 0000:00:1d.7
[   25.821947] usb usb1: configuration #1 chosen from 1 choice
[   25.822058] hub 1-0:1.0: USB hub found
[   25.822086] hub 1-0:1.0: 8 ports detected
[   25.852749] uhci_hcd: USB Universal Host Controller Interface driver
[   25.852867] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[   25.852889] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[   25.852899] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[   25.852940] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[   25.852996] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000c400
[   25.853222] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[   25.853233] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   25.853242] usb usb2: Product: UHCI Host Controller
[   25.853249] usb usb2: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[   25.853257] usb usb2: SerialNumber: 0000:00:1d.0
[   25.853696] usb usb2: configuration #1 chosen from 1 choice
[   25.853955] hub 2-0:1.0: USB hub found
[   25.853986] hub 2-0:1.0: 2 ports detected
[   25.855470] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[   25.855494] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[   25.855506] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[   25.855544] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[   25.855617] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000c480
[   25.855734] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[   25.855743] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   25.855752] usb usb3: Product: UHCI Host Controller
[   25.855759] usb usb3: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[   25.855766] usb usb3: SerialNumber: 0000:00:1d.1
[   25.855966] usb usb3: configuration #1 chosen from 1 choice
[   25.856115] hub 3-0:1.0: USB hub found
[   25.856140] hub 3-0:1.0: 2 ports detected
[   25.856301] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[   25.856324] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[   25.856334] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[   25.856364] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[   25.856434] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000c800
[   25.856545] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[   25.856555] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   25.856563] usb usb4: Product: UHCI Host Controller
[   25.856571] usb usb4: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[   25.856578] usb usb4: SerialNumber: 0000:00:1d.2
[   25.856809] usb usb4: configuration #1 chosen from 1 choice
[   25.856908] hub 4-0:1.0: USB hub found
[   25.856932] hub 4-0:1.0: 2 ports detected
[   25.857075] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[   25.857094] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[   25.857104] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[   25.857130] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[   25.857192] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000c880
[   25.857293] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[   25.857303] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   25.857311] usb usb5: Product: UHCI Host Controller
[   25.857317] usb usb5: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[   25.857324] usb usb5: SerialNumber: 0000:00:1d.3
[   25.857558] usb usb5: configuration #1 chosen from 1 choice
[   25.857654] hub 5-0:1.0: USB hub found
[   25.857683] hub 5-0:1.0: 2 ports detected
[   26.136064] usb 1-2: new high speed USB device using ehci_hcd and address 2
[   26.302655] usb 1-2: New USB device found, idVendor=093a, idProduct=2700
[   26.302674] usb 1-2: New USB device strings: Mfr=16, Product=97, SerialNumber=0
[   26.302687] usb 1-2: Manufacturer: PixArt Imaging Inc.
[   26.302945] usb 1-2: configuration #1 chosen from 1 choice
[   26.421064] usb 1-3: new high speed USB device using ehci_hcd and address 3
[   26.434127] cfg80211: Using static regulatory domain info
[   26.434136] cfg80211: Regulatory domain: US
[   26.434143]     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   26.434153]     (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
[   26.434162]     (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[   26.434172]     (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[   26.434181]     (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[   26.434190]     (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[   26.434200]     (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
[   26.434974] cfg80211: Calling CRDA for country: US
[   26.454185] eeepc_laptop: Eee PC Hotkey Driver
[   26.454804] eeepc_laptop: Hotkey init flags 0x41
[   26.455087] eeepc_laptop: TYPE (2000000) not reported by BIOS, enabling anyway
[   26.455101] eeepc_laptop: Get control methods supported: 0x2181711
[   26.458885] input: Asus EeePC extra buttons as /devices/platform/eeepc/input/input6
[   26.553909] usb 1-3: New USB device found, idVendor=058f, idProduct=6335
[   26.553928] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   26.553942] usb 1-3: Product: Mass Storage Device
[   26.553951] usb 1-3: Manufacturer: Generic
[   26.553960] usb 1-3: SerialNumber: 058F63356336
[   26.554241] usb 1-3: configuration #1 chosen from 1 choice
[   26.593593] elantech.c: assuming hardware version 1, firmware version 2.34
[   26.667670] elantech.c: Synaptics capabilities query result 0x10, 0x02, 0x64.
[   26.667684] elantech.c: firmware version 2.34 detected, enabling jumpy cursor workaround
[   27.106722] Initializing USB Mass Storage driver...
[   27.107026] scsi2 : SCSI emulation for USB Mass Storage devices
[   27.107275] usbcore: registered new interface driver usb-storage
[   27.107287] USB Mass Storage support registered.
[   27.107304] usb-storage: device found at 3
[   27.107309] usb-storage: waiting for device to settle before scanning
[   27.221611] input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio1/input/input7
[   27.229505] [drm] Initialized drm 1.1.0 20060810
[   27.240287] Linux video capture interface: v2.00
[   27.259962] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[   27.260076] HDA Intel 0000:00:1b.0: setting latency timer to 64
[   27.569638] uvcvideo: Found UVC 1.00 device <unnamed> (093a:2700)
[   27.578578] input: UVC Camera (093a:2700) as /devices/pci0000:00/0000:00:1d.7/usb1/1-2/1-2:1.0/input/input8
[   27.578753] usbcore: registered new interface driver uvcvideo
[   27.578765] USB Video Class driver (v0.1.0)
[   27.713200] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input9
[   27.715788] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   27.715802] i915 0000:00:02.0: setting latency timer to 64
[   27.728529] [drm] set up 7M of stolen space
[   27.833721] composite sync not supported
[   27.834298] [drm] initialized overlay support
[   27.848916] ath5k 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[   27.848939] ath5k 0000:02:00.0: setting latency timer to 64
[   27.849038] ath5k 0000:02:00.0: registered as 'phy0'
[   28.262537] composite sync not supported
[   28.349726] ath: EEPROM regdomain: 0x60
[   28.349732] ath: EEPROM indicates we should expect a direct regpair map
[   28.349740] ath: Country alpha2 being used: 00
[   28.349745] ath: Regpair used: 0x60
[   28.544091] Console: switching to colour frame buffer device 128x37
[   28.551912] fb0: inteldrmfb frame buffer device
[   28.551917] registered panic notifier
[   28.551936] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[   28.649259] phy0: Selected rate control algorithm 'minstrel'
[   28.650848] Registered led device: ath5k-phy0::rx
[   28.650906] Registered led device: ath5k-phy0::tx
[   28.650917] ath5k phy0: Atheros AR2425 chip found (MAC: 0xe2, PHY: 0x70)
[   31.725147] loop: module loaded
[   32.104396] usb-storage: device scan complete
[   32.105122] scsi 2:0:0:0: Direct-Access     Single   Flash Reader     1.00 PQ: 0 ANSI: 0
[   32.415553] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[   32.937491] Adding 1998840k swap on /dev/mapper/EeePC--900HA-swap_1.  Priority:-1 extents:1 across:1998840k 
[   37.324423] fuse init (API version 7.13)
[   43.048519] Bluetooth: Core ver 2.15
[   43.048519] NET: Registered protocol family 31
[   43.048519] Bluetooth: HCI device and connection manager initialized
[   43.048519] Bluetooth: HCI socket layer initialized
[   43.240552] Bluetooth: L2CAP ver 2.14
[   43.240559] Bluetooth: L2CAP socket layer initialized
[   43.686134] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   43.686144] Bluetooth: BNEP filters: protocol multicast
[   44.016406] Bridge firewalling registered
[   44.284829] Bluetooth: SCO (Voice Link) ver 0.6
[   44.284837] Bluetooth: SCO socket layer initialized
[   50.835283] composite sync not supported
[   50.982916] composite sync not supported
[   58.622375] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   64.457600] ATL1E 0000:01:00.0: irq 27 for MSI/MSI-X
[   64.458267] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   67.709014] composite sync not supported
[   67.866032] composite sync not supported
[   68.108617] composite sync not supported
[   69.419706] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   69.839119] ATL1E 0000:01:00.0: irq 27 for MSI/MSI-X
[   69.840115] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   69.916251] CPU0 attaching NULL sched-domain.
[   69.916262] CPU1 attaching NULL sched-domain.
[   69.937241] CPU0 attaching sched-domain:
[   69.937258]  domain 0: span 0-1 level SIBLING
[   69.937271]   groups: 0 (cpu_power = 589) 1 (cpu_power = 589)
[   69.937296]   domain 1: span 0-1 level MC
[   69.937307]    groups: 0-1 (cpu_power = 1178)
[   69.937328] CPU1 attaching sched-domain:
[   69.937338]  domain 0: span 0-1 level SIBLING
[   69.937349]   groups: 1 (cpu_power = 589) 0 (cpu_power = 589)
[   69.937372]   domain 1: span 0-1 level MC
[   69.937383]    groups: 0-1 (cpu_power = 1178)
[   70.199415] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   74.721506] wlan0: direct probe to AP 00:22:3f:88:53:ca (try 1)
[   74.723635] wlan0: direct probe responded
[   74.723647] wlan0: authenticate with AP 00:22:3f:88:53:ca (try 1)
[   74.725559] wlan0: authenticated
[   74.725616] wlan0: associate with AP 00:22:3f:88:53:ca (try 1)
[   74.727893] wlan0: RX AssocResp from 00:22:3f:88:53:ca (capab=0x411 status=0 aid=3)
[   74.727905] wlan0: associated
[   74.729775] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   77.945923] composite sync not supported
[   85.232493] wlan0: no IPv6 routers present
[  102.453319] eeepc_laptop: BIOS says wireless lan is blocked, but the pci device is present
[  102.453330] eeepc_laptop: skipped wireless hotplug as probably inappropriate for this model
[  102.553454] eeepc_laptop: BIOS says wireless lan is blocked, but the pci device is present
[  102.553465] eeepc_laptop: skipped wireless hotplug as probably inappropriate for this model
[  102.564146] wlan0: deauthenticating from 00:22:3f:88:53:ca by local choice (reason=3)
[  102.660646] ath5k phy0: failed to wakeup the MAC Chip
[  106.754766] ATL1E 0000:01:00.0: irq 27 for MSI/MSI-X
[  106.755527] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  116.451238] ath5k phy0: failed to wakeup the MAC Chip
[  116.451253] ath5k phy0: can't reset hardware (-5)
[  121.460385] ath5k phy0: failed to wakeup the MAC Chip
[  121.460403] ath5k phy0: can't reset hardware (-5)
[  124.280305] ath5k phy0: failed to wakeup the MAC Chip
[  124.280319] ath5k phy0: can't reset hardware (-5)
[  132.628856] ath5k phy0: failed to wakeup the MAC Chip
[  132.628871] ath5k phy0: can't reset hardware (-5)

2. lspci

text

    Capabilities: [d0] Power Management version 2
        Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
        Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Kernel driver in use: i915

00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03)
    Subsystem: ASUSTeK Computer Inc. Device 8340
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Region 0: Memory at f3e80000 (32-bit, non-prefetchable) [size=512K]
    Capabilities: [d0] Power Management version 2
        Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
        Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-


00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02)
    Subsystem: ASUSTeK Computer Inc. Device 8330
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 32 bytes
    Interrupt: pin A routed to IRQ 22
    Region 0: Memory at f3db8000 (64-bit, non-prefetchable) [size=16K]
    Capabilities: [50] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
        Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [60] MSI: Enable- Count=1/1 Maskable- 64bit+
        Address: 0000000000000000  Data: 0000
    Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
        DevCap:    MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
            ExtTag- RBE- FLReset-
        DevCtl:    Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
            RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
            MaxPayload 128 bytes, MaxReadReq 128 bytes
        DevSta:    CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
        LnkCap:    Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
            ClockPM- Surprise- LLActRep- BwNot-
        LnkCtl:    ASPM Disabled; Disabled- Retrain- CommClk-
            ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
        LnkSta:    Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
    Capabilities: [100 v1] Virtual Channel
        Caps:    LPEVC=0 RefClk=100ns PATEntryBits=1
        Arb:    Fixed- WRR32- WRR64- WRR128-
        Ctrl:    ArbSelect=Fixed
        Status:    InProgress-
        VC0:    Caps:    PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
            Arb:    Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
            Ctrl:    Enable+ ID=0 ArbSelect=Fixed TC/VC=01
            Status:    NegoPending- InProgress-
        VC1:    Caps:    PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
            Arb:    Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
            Ctrl:    Enable- ID=0 ArbSelect=Fixed TC/VC=00
            Status:    NegoPending- InProgress-
    Capabilities: [130 v1] Root Complex Link
        Desc:    PortNumber=0f ComponentID=00 EltType=Config
        Link0:    Desc:    TargetPort=00 TargetComponent=00 AssocRCRB- LinkType=MemMapped LinkValid+
            Addr:    00000000fed1c000
    Kernel driver in use: HDA Intel


00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02) (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 32 bytes
    Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
    I/O behind bridge: 00001000-00001fff
    Memory behind bridge: 40000000-401fffff
    Prefetchable memory behind bridge: 0000000040200000-00000000403fffff
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
    BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
        PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
        DevCap:    MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
            ExtTag- RBE- FLReset-
        DevCtl:    Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
            RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
            MaxPayload 128 bytes, MaxReadReq 128 bytes
        DevSta:    CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
        LnkCap:    Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <4us
            ClockPM- Surprise- LLActRep+ BwNot-
        LnkCtl:    ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
            ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
        LnkSta:    Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
        SltCap:    AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
            Slot #0, PowerLimit 0.000W; Interlock- NoCompl-
        SltCtl:    Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
            Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
        SltSta:    Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
            Changed: MRL- PresDet- LinkState-
        RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
        RootCap: CRSVisible-
        RootSta: PME ReqID 0000, PMEStatus- PMEPending-
    Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
        Address: fee0300c  Data: 4161
    Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 830f
    Capabilities: [a0] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
        Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [100 v1] Virtual Channel
        Caps:    LPEVC=0 RefClk=100ns PATEntryBits=1
        Arb:    Fixed+ WRR32- WRR64- WRR128-
        Ctrl:    ArbSelect=Fixed
        Status:    InProgress-
        VC0:    Caps:    PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
            Arb:    Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
            Ctrl:    Enable+ ID=0 ArbSelect=Fixed TC/VC=01
            Status:    NegoPending- InProgress-
        VC1:    Caps:    PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
            Arb:    Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
            Ctrl:    Enable- ID=0 ArbSelect=Fixed TC/VC=00
            Status:    NegoPending- InProgress-
    Capabilities: [180 v1] Root Complex Link
        Desc:    PortNumber=01 ComponentID=00 EltType=Config
        Link0:    Desc:    TargetPort=00 TargetComponent=00 AssocRCRB- LinkType=MemMapped LinkValid+
            Addr:    00000000fed1c001
    Kernel driver in use: pcieport


00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 02) (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 32 bytes
    Bus: primary=00, secondary=02, subordinate=03, sec-latency=0
    I/O behind bridge: 0000e000-0000efff
    Memory behind bridge: f4000000-fbffffff
    Prefetchable memory behind bridge: 00000000ec000000-00000000f2ffffff
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
    BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
        PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
        DevCap:    MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
            ExtTag- RBE- FLReset-
        DevCtl:    Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
            RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
            MaxPayload 128 bytes, MaxReadReq 128 bytes
        DevSta:    CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
        LnkCap:    Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
            ClockPM- Surprise- LLActRep+ BwNot-
        LnkCtl:    ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
            ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
        LnkSta:    Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
        SltCap:    AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
            Slot #0, PowerLimit 0.000W; Interlock- NoCompl-
        SltCtl:    Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
            Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
        SltSta:    Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
            Changed: MRL- PresDet+ LinkState+
        RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
        RootCap: CRSVisible-
        RootSta: PME ReqID 0000, PMEStatus- PMEPending-
    Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
        Address: fee0300c  Data: 4169
    Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 830f
    Capabilities: [a0] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
        Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [100 v1] Virtual Channel
        Caps:    LPEVC=0 RefClk=100ns PATEntryBits=1
        Arb:    Fixed+ WRR32- WRR64- WRR128-
        Ctrl:    ArbSelect=Fixed
        Status:    InProgress-
        VC0:    Caps:    PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
            Arb:    Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
            Ctrl:    Enable+ ID=0 ArbSelect=Fixed TC/VC=01
            Status:    NegoPending- InProgress-
        VC1:    Caps:    PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
            Arb:    Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
            Ctrl:    Enable- ID=0 ArbSelect=Fixed TC/VC=00
            Status:    NegoPending- InProgress-
    Capabilities: [180 v1] Root Complex Link
        Desc:    PortNumber=02 ComponentID=00 EltType=Config
        Link0:    Desc:    TargetPort=00 TargetComponent=00 AssocRCRB- LinkType=MemMapped LinkValid+
            Addr:    00000000fed1c001
    Kernel driver in use: pcieport


00:1c.3 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 4 (rev 02) (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 32 bytes
    Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
    I/O behind bridge: 0000d000-0000dfff
    Memory behind bridge: f3f00000-f3ffffff
    Prefetchable memory behind bridge: 0000000040400000-00000000405fffff
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
    BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
        PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
        DevCap:    MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
            ExtTag- RBE- FLReset-
        DevCtl:    Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
            RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
            MaxPayload 128 bytes, MaxReadReq 128 bytes
        DevSta:    CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
        LnkCap:    Port #4, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
            ClockPM- Surprise- LLActRep+ BwNot-
        LnkCtl:    ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
            ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
        LnkSta:    Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
        SltCap:    AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
            Slot #0, PowerLimit 0.000W; Interlock- NoCompl-
        SltCtl:    Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
            Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
        SltSta:    Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
            Changed: MRL- PresDet+ LinkState+
        RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
        RootCap: CRSVisible-
        RootSta: PME ReqID 0000, PMEStatus- PMEPending-
    Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
        Address: fee0300c  Data: 4171
    Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 830f
    Capabilities: [a0] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
        Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [100 v1] Virtual Channel
        Caps:    LPEVC=0 RefClk=100ns PATEntryBits=1
        Arb:    Fixed+ WRR32- WRR64- WRR128-
        Ctrl:    ArbSelect=Fixed
        Status:    InProgress-
        VC0:    Caps:    PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
            Arb:    Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
            Ctrl:    Enable+ ID=0 ArbSelect=Fixed TC/VC=01
            Status:    NegoPending- InProgress-
        VC1:    Caps:    PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
            Arb:    Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
            Ctrl:    Enable- ID=0 ArbSelect=Fixed TC/VC=00
            Status:    NegoPending- InProgress-
    Capabilities: [180 v1] Root Complex Link
        Desc:    PortNumber=04 ComponentID=00 EltType=Config
        Link0:    Desc:    TargetPort=00 TargetComponent=00 AssocRCRB- LinkType=MemMapped LinkValid+
            Addr:    00000000fed1c001
    Kernel driver in use: pcieport


00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 02) (prog-if 00 [UHCI])
    Subsystem: ASUSTeK Computer Inc. Device 830f
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin A routed to IRQ 23
    Region 4: I/O ports at c400 [size=32]
    Kernel driver in use: uhci_hcd


00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02) (prog-if 00 [UHCI])
    Subsystem: ASUSTeK Computer Inc. Device 830f
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin B routed to IRQ 19
    Region 4: I/O ports at c480 [size=32]
    Kernel driver in use: uhci_hcd


00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI])
    Subsystem: ASUSTeK Computer Inc. Device 830f
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin C routed to IRQ 18
    Region 4: I/O ports at c800 [size=32]
    Kernel driver in use: uhci_hcd


00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02) (prog-if 00 [UHCI])
    Subsystem: ASUSTeK Computer Inc. Device 830f
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin D routed to IRQ 16
    Region 4: I/O ports at c880 [size=32]
    Kernel driver in use: uhci_hcd


00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02) (prog-if 20 [EHCI])
    Subsystem: ASUSTeK Computer Inc. Device 830f
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin A routed to IRQ 23
    Region 0: Memory at f3db7c00 (32-bit, non-prefetchable) [size=1K]
    Capabilities: [50] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
        Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [58] Debug port: BAR=1 offset=00a0
    Kernel driver in use: ehci_hcd


00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) (prog-if 01 [Subtractive decode])
    Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
    I/O behind bridge: 0000f000-00000fff
    Memory behind bridge: fff00000-000fffff
    Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
    Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
    BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
        PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Capabilities: [50] Subsystem: ASUSTeK Computer Inc. Device 830f


00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02)
    Subsystem: ASUSTeK Computer Inc. Device 830f
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Capabilities: [e0] Vendor Specific Information: Len=0c <?>


00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02) (prog-if 80 [Master])
    Subsystem: ASUSTeK Computer Inc. Device 830f
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
    Latency: 0
    Interrupt: pin B routed to IRQ 19
    Region 0: I/O ports at 01f0 [size=8]
    Region 1: I/O ports at 03f4 [size=1]
    Region 2: I/O ports at 0170 [size=8]
    Region 3: I/O ports at 0374 [size=1]
    Region 4: I/O ports at ffa0 [size=16]
    Capabilities: [70] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
        Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Kernel driver in use: ata_piix


01:00.0 Ethernet controller: Atheros Communications AR8121/AR8113/AR8114 Gigabit or Fast Ethernet (rev b0)
    Subsystem: ASUSTeK Computer Inc. Device 8324
    Physical Slot: eeepc-wifi
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 32 bytes
    Interrupt: pin A routed to IRQ 27
    Region 0: Memory at f3fc0000 (64-bit, non-prefetchable) [size=256K]
    Region 2: I/O ports at dc00 [size=128]
    Capabilities: [40] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
        Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [48] MSI: Enable+ Count=1/1 Maskable- 64bit+
        Address: 00000000fee0300c  Data: 41a1
    Capabilities: [58] Express (v1) Endpoint, MSI 00
        DevCap:    MaxPayload 4096 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
            ExtTag- AttnBtn+ AttnInd+ PwrInd+ RBE- FLReset-
        DevCtl:    Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
            RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
            MaxPayload 128 bytes, MaxReadReq 512 bytes
        DevSta:    CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend-
        LnkCap:    Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 unlimited, L1 unlimited
            ClockPM- Surprise- LLActRep- BwNot-
        LnkCtl:    ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
            ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
        LnkSta:    Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
    Capabilities: [6c] Vital Product Data
        Unknown small resource type 0b, will not decode more.
    Capabilities: [100 v1] Advanced Error Reporting
        UESta:    DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
        UEMsk:    DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
        UESvrt:    DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
        CESta:    RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
        CEMsk:    RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
        AERCap:    First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-
    Capabilities: [180 v1] Device Serial Number ff-05-b8-d0-e0-cb-4e-ff
    Kernel driver in use: ATL1E


02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)
    Subsystem: AzureWave AR5007EG 802.11bg Wi-Fi mini PCI express card
    Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Interrupt: pin A routed to IRQ 17
    Region 0: Memory at fbff0000 (64-bit, non-prefetchable) [disabled] [size=64K]
    Capabilities: [40] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
        Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit-
        Address: 00000000  Data: 0000
    Capabilities: [60] Express (v1) Legacy Endpoint, MSI 00
        DevCap:    MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
            ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
        DevCtl:    Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
            RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
            MaxPayload 128 bytes, MaxReadReq 512 bytes
        DevSta:    CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
        LnkCap:    Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
            ClockPM- Surprise- LLActRep- BwNot-
        LnkCtl:    ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk-
            ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
        LnkSta:    Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
    Capabilities: [90] MSI-X: Enable- Count=1 Masked-
        Vector table: BAR=0 offset=00000000
        PBA: BAR=0 offset=00000000
    Capabilities: [100 v1] Advanced Error Reporting
        UESta:    DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
        UEMsk:    DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
        UESvrt:    DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
        CESta:    RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
        CEMsk:    RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
        AERCap:    First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-
    Capabilities: [140 v1] Virtual Channel
        Caps:    LPEVC=0 RefClk=100ns PATEntryBits=1
        Arb:    Fixed- WRR32- WRR64- WRR128-
        Ctrl:    ArbSelect=Fixed
        Status:    InProgress-
        VC0:    Caps:    PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
            Arb:    Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
            Ctrl:    Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
            Status:    NegoPending- InProgress-
    Kernel driver in use: ath5k
21.01.2011 01:55 #119201

vlav, ставим пакет rfkill и показываем

rfkill list

покажите за одно

aptitude search firmware | grep ^i
21.01.2011 09:56 #119227

rfkill - был установлен.
вывод терминала:

text

0: eeepc-wlan: Wireless LAN
    Soft blocked: no
    Hard blocked: no
1: phy0: Wireless LAN
    Soft blocked: no
    Hard blocked: no

после двухкратного Fn-F2 - то же самое:

text

0: eeepc-wlan: Wireless LAN
    Soft blocked: no
    Hard blocked: no
1: phy0: Wireless LAN
    Soft blocked: no
    Hard blocked: no

Команда
aptitude search firmware | grep ^i
вызывает просто переход на следующую строку - ничего не выводится.

21.01.2011 12:02 #119282
vlav написал:

Команда
aptitude search firmware | grep ^i
вызывает просто переход на следующую строку - ничего не выводится.

Если ничего не выводиться значит установленных firmware(прошивки) нет.Попробуй установить:firmware-linux-nonfree.

21.01.2011 12:16 #119287
ABulychev написал:
Попробуй установить:firmware-linux-nonfree.

В пакете в списке блобов не упомянут Atheros.
Кроме того, ведь если бы ядро не поддерживало карту, Wi-Fi не было бы ни при каких обстоятельствах, а не только после выключения / повторного включения, не так ли?

21.01.2011 17:09 · отредактировано #119393

У меня была подобная проблема(у меня тоже EeePC), только тогда я устанавливал Lenny.С ядром 2.6.26 вообще не было поддержки карт atheros ... драйвера настроил, но загружалось все это как у тебя и данную проблему решить до конца не мог.Затем решил поставить squeeze и все мои проблемы решились разом.
Посмотри пакет firmware-atheros, но там по-моему опять нет поддержки твоей карты. А eeepc-acpi-scripts не пробывал ставить? И еще посмотри вот эту ссылку http://wiki.debian.org/ath5k .

21.01.2011 23:17 #119566
ABulychev написал:
А eeepc-acpi-scripts не пробывал ставить?

eeepc-acpi-scripts у меня стоит.

Войдите или зарегистрируйтесь, чтобы ответить.